ADA4433-1WBCPZ-R7
Product Specifications
ADA4433-1WBCPZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADA4433-1WBCPZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADA4433-1WBCPZ-R7: differential SD video filter with short to battery protection
The ADA4433-1WBCPZ-R7 is a standard definition video filter with a differential output, a fifth order low pass response and protection against an output short to a battery of up to 18 V. It is the automotive part in the pair: the ADA4432-1 is the single ended version and this one drives a twisted pair to a remote display or an electronic control unit. Quiescent current is 13.2 mA and the power down state is 13.5 uA.
Published values
| Parameter | Value |
|---|---|
| Filter | fifth order low pass, differential output |
| -3 dB bandwidth | 10 MHz |
| 0.1 dB gain flatness | to 3 MHz |
| Rejection at 27 MHz | 45 dB |
| Quiescent current | 13.2 mA typical |
| Power down current | 13.5 uA typical |
| Supply range | 2.6 V to 3.6 V |
| Output protection | short to battery up to 18 V, short to ground |
| Diagnostic output | short to battery flag |
| Qualification | AEC-Q100 for automotive applications |
| Temperature range | -40 C to +125 C |
| Package | 8-lead 3 mm by 3 mm LFCSP |
Why differential on a camera link
A composite video signal that travels a metre inside a vehicle body picks up the alternator, the ignition and the motor drives. A differential pair carries the same signal on two wires with opposite polarity, so what the harness picks up appears as a common mode voltage and is removed at the receiver. The filter does not have to be sharper for that reason, and the 10 MHz -3 dB point with 45 dB of rejection at 27 MHz is enough to keep the sampling clock out of the picture.
The 0.1 dB flatness figure only holds to 3 MHz. For an NTSC signal, whose chroma subcarrier is at 3.58 MHz, that is the region that decides colour accuracy, and a filter with a 10 MHz -3 dB point but a 1 MHz flatness point would shift the colour rather than the detail.
18 V of protection on a 3.3 V part
The output survives a short to a battery of up to 18 V, which is more than five times its own supply. That is not a data sheet formality: a camera harness that is miswired in service sees the battery on the video line, and without the protection the coupling capacitor and the output stage are the first casualties. The device also survives a short to ground, which is what a pinched harness gives.
The short to battery condition raises a flag that the host can read, so a diagnostic trouble code can be set without an extra comparator and divider on the board. That flag is the part of the feature set that turns a protection device into a diagnosable one.
Current, heat and the 3.3 V rail
13.2 mA at 3.3 V is 43.6 mW, which the 3 mm by 3 mm LFCSP passes through its exposed pad without a heat sink. The power down current of 13.5 uA is what a parked vehicle needs: a camera that is not being viewed still has a supply connected, and 13.2 mA per camera across a parked week is 2.2 Ah, which is a battery that will not start the car.
The 2.6 V to 3.6 V range means the part runs from the same 3.3 V rail as the image sensor and the serialiser, so the camera module needs one regulator rather than two. The lower limit of 2.6 V leaves 700 mV of headroom on a 3.3 V rail at minus five percent, which is the tolerance a automotive rail is allowed.
The pages that answer this most often are component obsolescence management for the family alternatives, medical device components for the acceptance test, and how to verify a drop in replacement for the case where a replacement has to be fitted before the next build.
Two questions buyers ask
Is the ADA4433-1 a drop in for the ADA4432-1? No. The ADA4432-1 has a single ended output and is available in a 6-lead SOT-23, while this part has a differential output in an 8-lead LFCSP. The two are the same filter core with different output stages, and the receiver has to match the output type.
Does the differential output need a coupling capacitor on each line? It can be dc coupled because the output offset is defined, and ac coupling is used where the receiver has its own bias. Two capacitors of the same value are needed, and their tolerance becomes a common mode to differential conversion term that the receiver has to tolerate.