ADA4412-3ARQZ-R7
Product Specifications
ADA4412-3ARQZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADA4412-3ARQZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADA4412-3ARQZ-R7: triple sixth order video filter with selectable 36, 18 and 9 MHz cutoffs
The ADA4412-3ARQZ-R7 is a three channel video reconstruction filter in a 20-lead QSOP. Each channel is a sixth order low pass block with a fixed gain of 2, and two logic pins select 36 MHz, 18 MHz or 9 MHz so one board can serve RGB, high definition component video and standard definition video without a second bill of materials. The output is rail to rail and swings 4.5 V peak to peak on a single 5 V supply.
Published values
| Parameter | Value |
|---|---|
| Filter order | sixth order, three channels |
| Selectable cutoff | 36 MHz, 18 MHz and 9 MHz, set by two logic pins |
| -1 dB bandwidth in high definition mode | 31.5 MHz |
| Fixed gain | 2, non inverting |
| Output swing | 4.5 V peak to peak on a single 5 V supply |
| Supply range | +4.5 V single supply to plus or minus 5 V split supply |
| Quiescent power | 265 mW for three channels at 5 V |
| Disable current | 10 uA typical |
| Output offset adjustment | plus or minus 500 mV, input referred, continuously adjustable |
| Load drive | two 75 ohm doubly terminated cables per channel |
| Temperature range | -40 C to +85 C |
| Package | 20-lead QSOP |
What the cutoff selection is for
A 1080i signal carries picture detail to about 30 MHz, so the 36 MHz setting with its 31.5 MHz -1 dB point passes the picture and stops the sampling image that sits above it. A 720p or 1080i source that is filtered at 9 MHz looks soft, and an SD source filtered at 36 MHz passes the clock energy that shows up as a herringbone pattern. The two logic pins are therefore a picture quality decision and not a configuration detail.
A sixth order response falls at 120 dB per decade, so the 27 MHz residue that a 9 MHz setting has to remove is a long way down. That steepness is the reason a passive LC network is not a substitute at this board size: three channels of sixth order LC filtering occupy more area than the 20-lead QSOP and need their own tuning.
Power and the disable pin
Three channels at 5 V draw 265 mW, which is 53 mA total or about 17.7 mA per channel, and that is the quiescent figure before the output stage drives a cable. The disable pin drops the supply current to 10 uA, which matters in a set top box that has to meet a standby power budget while the video path is still connected to the television.
The output stage is specified to drive two 75 ohm doubly terminated cables, which is a 37.5 ohm load, and it swings 4.5 V peak to peak on a 5 V rail. A 4.5 V peak to peak signal into 37.5 ohm is 54 mA of peak current per channel, so the supply and the decoupling have to be sized for the peak and not for the quiescent number.
Offset control and coupling
The offset input adjusts the output over plus or minus 500 mV referred to the input, which at a gain of 2 is plus or minus 1 V at the output. That is enough to move a video signal that sits at the wrong dc level into the range of the encoder or the display, without an extra clamp stage.
The inputs and outputs can be dc coupled or ac coupled, and the choice decides whether the offset control is useful. With ac coupling the offset at the output is removed by the capacitor and the control only shifts the operating point of the amplifier. With dc coupling the offset control is a real level shift and the input common mode range of the following stage has to be checked.
Two pages worth reading before a purchase order goes out are component lead time solutions and one stop BOM sourcing; the first lists what else fits the socket, the second is the test sequence for a drop in, and vendor consolidation covers the case where the shortage is already on the line.
Two questions buyers ask
Can one ADA4412-3 serve RGB and composite video on the same board? Yes, if the two modes are not needed at the same time: the cutoff is a pin setting, so the three channels move together. A board that has to show RGB and composite simultaneously needs two devices.
Is the 265 mW figure per channel? No. It is the total for the three channels at 5 V, which is 53 mA of supply current. The output current into a terminated cable comes on top of that and depends on the picture.