AD8674ARZ-REEL7
Product Specifications
AD8674ARZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8674ARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8674ARZ-REEL7: 2.8 nV of Amplifier Noise Beside a 12.8 nV Resistor
The AD8674ARZ-REEL7 is a quad precision operational amplifier with 2.8 nV per root Hz voltage noise, 77 nV peak to peak from 0.1 Hz to 10 Hz, 10 MHz gain bandwidth, 12 nA maximum input bias current, 75 uV maximum offset voltage and 120 dB minimum open loop gain. Each amplifier draws 3 mA typical, the supply range is plus or minus 5 V to plus or minus 15 V, the part is unity gain stable and has no phase reversal. Analog Devices lists five part models from $5.31 at 1ku, in an SOIC body with the ARZ suffix.
The source resistance sets the noise floor, not the amplifier
A 10 kohm resistor at 25 C produces 12.8 nV per root Hz of thermal noise on its own. Adding a 2.8 nV amplifier in front of it gives 13.1 nV per root Hz, only 2 percent worse than the resistor alone. Over a 10 kHz bandwidth that is 1.31 uV rms, and over 20 kHz it is 1.86 uV rms. The practical conclusion is that below about 1 kohm of source resistance the amplifier dominates and the 2.8 nV matters, while above about 10 kohm the resistor dominates and a more expensive amplifier buys nothing.
Bias current becomes offset when the source is resistive
12 nA of bias current through 10 kohm is 120 uV. That is larger than the 75 uV maximum offset voltage of the amplifier itself, so the two add to 195 uV of worst case input referred error before any drift is counted. A buyer comparing only the offset column will understate the error in a high impedance circuit. Where the source is low impedance, the bias term collapses and the 75 uV stands alone.
Four amplifiers in one body and the supply current that follows
At 3 mA per amplifier, four channels draw 12 mA. On a plus or minus 15 V supply that is 360 mW in one package, which is the first thermal question in a four channel board. The 10 MHz gain bandwidth also falls away with gain: at a closed loop gain of 100 the usable bandwidth is about 100 kHz, and at 1000 it is about 10 kHz. With 120 dB of open loop gain, the gain error at 100 is 0.01 percent and at 1000 it is 0.1 percent.
The published table, as the vendor states it
| Parameter | Value |
|---|---|
| Configuration | Quad operational amplifier |
| Voltage noise | 2.8 nV per root Hz, 77 nV peak to peak |
| Gain bandwidth | 10 MHz |
| Input bias current | 12 nA maximum |
| Offset voltage | 75 uV maximum |
| Open loop gain | 120 dB minimum |
| Supply current | 3 mA typical per amplifier |
| Supply range | plus or minus 5 V to plus or minus 15 V |
| Stability | unity gain stable, no phase reversal |
| Part models and price | 5 models, from $5.31 at 1ku |
Where a quad earns its board area
Four channels in one body share one thermal environment, which matters in a multi-pole filter where the four stages should track over temperature. It also removes three packages and the associated decoupling from a board. The cost is that all four channels dissipate in one place, so the 360 mW figure has to be checked against the package thermal resistance before the board is committed.
Buyer questions
Does a 2.8 nV amplifier make a 10 kohm circuit quiet? No. The 10 kohm resistor already produces 12.8 nV per root Hz, so the amplifier contributes about 2 percent of the total noise power. The 2.8 nV figure pays off in low source impedance work, such as a 100 ohm bridge or a current sense shunt, not in a high impedance node.
Is the 75 uV offset the total error? Only with a zero ohm source. Add the bias current times the source resistance, which is 120 uV at 10 kohm, and add the drift terms over temperature. The datasheet offset is one term in a budget, not the budget.
Family page for the category: Analog and mixed-signal ICs. For amplifier alternates across brands see Amplifier cross reference, and for long lead time planning on precision analog parts see component lead time solutions.
Request Quote — In Stock, 100% New & Original, Full Warranty