AD8666ARMZ
Product Specifications
AD8666ARMZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8666ARMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8666ARMZ: dual 16 volt 4 MHz CMOS amplifier in MSOP
The AD8666ARMZ is the two channel member of the AD8665/AD8666/AD8668 16 V CMOS family in an 8-lead MSOP body. It has a 2.5 mV maximum offset, 1 pA of bias current and 8 to 10 nV/root Hz of noise at 4 MHz of gain bandwidth, on 1.4 mA per amplifier at 5 V and 1.55 mA at 16 V.
Published values
| Parameter | Value |
|---|---|
| Offset voltage | 0.7 mV typical, 2.5 mV maximum at 5 V; 0.6 mV typical at 16 V |
| Offset voltage drift | 3 uV/C typical, 10 uV/C maximum |
| Input bias current | 0.2 pA typical, 1 pA maximum |
| Supply current per amplifier | 1.1 mA typical, 1.4 mA maximum at 5 V; 1.55 mA at 16 V |
| Gain bandwidth | 4 MHz |
| Slew rate | 3.5 V/us |
| Voltage noise density | 10 nV/root Hz at 1 kHz, 8 nV/root Hz at 10 kHz |
| CMRR | 84 dB minimum at 5 V, 90 dB minimum at 16 V |
| Input voltage range | -0.1 V to +3.0 V at 5 V; -0.1 V to +14 V at 16 V |
| Output swing at 1 mA | 4.88 V minimum high, 50 mV typical low at 5 V |
| Short circuit output current | 19 mA at 5 V, 140 mA at 16 V |
| Phase margin | 70 degrees at 5 V, 73 degrees at 16 V |
| Supply range | 5 V to 16 V single supply, +-2.5 V to +-8 V dual |
A 16 V CMOS input stage
The bias current of 1 pA is what a CMOS input buys, and it holds across the supply range. A 10 MOhm source therefore sees 10 uV of bias error, which is the same order as the 2.5 mV offset, so the offset is the limit and not the bias current. On a 1 MOhm source the bias error is 1 uV and irrelevant.
The input window of -0.1 V to +3.0 V at 5 V is the constraint to read carefully: the part runs to 16 V but at 5 V it cannot take a signal to the rail. At 16 V the window is -0.1 V to +14 V, so a 0 V to 10 V signal fits and a signal that swings to 16 V does not. The output, by contrast, is rail to rail within the 50 to 85 mV in the table.
2.5 mV and 10 uV/C in a cost part
2.5 mV maximum offset with 10 uV/C of drift is a general purpose combination: 1.65 mV of drift over the full range against an offset of 2.5 mV, so the part moves by most of its own offset over temperature. On a 1 V signal that is 0.25 percent of error at room temperature and 0.4 percent over temperature. That is fine for a control loop, a filter or a buffer and not fine for a measurement that has to hold 0.1 percent.
8 to 10 nV/root Hz of noise over a 100 kHz band is 2.5 to 3.2 uV rms, which is 33 codes of a 16-bit converter on 5 V. Like every general purpose amplifier, the part is a 12-bit device in noise terms unless the band is narrowed.
19 mA at 5 V and 140 mA at 16 V
The short circuit current rises with supply, from 19 mA at 5 V to 140 mA at 16 V, which is a real difference for a part that drives a cable or a transducer. At 16 V the output can deliver a 10 V swing into 600 ohm, which is 16 mA, and the 140 mA limit only appears on a fault. The 140 mA figure also raises the dissipation during that fault: 16 V at 140 mA is 2.2 W in a small body, so a permanent short will destroy the part and the supply needs to survive that.
1.55 mA at 16 V is 25 mW per channel, so a dual is 50 mW, which the MSOP passes with a small rise. The supply current is what limits this part at 16 V, not the package.
Buyers usually arrive at the amplifier cross reference to find the family alternatives, then use how to verify a drop in replacement to confirm a substitute before it is fitted; OEM procurement is the routine for a part that has already stopped shipping.
Two questions buyers ask
Is the AD8666 rail to rail on the input? No. The output is rail to rail; the input window is -0.1 V to +3 V at 5 V and -0.1 V to +14 V at 16 V. A signal within 2 V of the positive rail is outside the part.
What is the precision version of this amplifier? The AD8667, which is a 16 V CMOS dual with a 175 uV offset at 5 V on 250 uA per amplifier. It is slower, at 520 kHz, and much lower in current.