Contact Us

AD8642ARZ

Brand: Analog Devices
Analog Devices AD8642ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8642ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8642ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8642ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8642ARZ: dual JFET input amplifier for high impedance sensors

The AD8642ARZ is the two channel member of the AD8641/AD8642/AD8643 JFET input family in an 8-lead SOIC_N body. It draws 250 uA maximum per amplifier, holds a 750 uV maximum offset with 1 pA maximum bias current, and runs from 5 V to 26 V single supply, which is the shape of a photodiode or pH front end on an industrial rail.

Published values

ParameterValue
Offset voltage50 uV typical, 750 uV maximum
Offset voltage drift2.5 uV/C
Input bias current0.25 pA typical, 1 pA maximum, -40 to +125 C
Input offset current0.5 pA maximum
Supply current per amplifier195 uA typical, 250 uA maximum at 5 V; 200 uA at +-13 V
Gain bandwidth3 MHz at 5 V, 3.5 MHz at +-13 V
Slew rate2 V/us at 5 V, 3 V/us at +-13 V
Voltage noise density28.5 nV/root Hz at 1 kHz, 4.0 uV p-p over 0.1 to 10 Hz
CMRR74 dB minimum at 5 V, 90 dB minimum at +-13 V
Input voltage range0 V to +3 V on a 5 V supply; -13 V to +10 V on a +-13 V supply
Output swing4.95 V minimum high on a 5 V supply
Phase margin50 degrees at 5 V
Supply range5 V to 26 V single supply, +-2.5 V to +-13 V dual

What 1 pA buys a photodiode

A photodiode with 1 nA of signal current and 1 pA of amplifier bias current loses 0.1 percent of the signal to the amplifier, so the bias current is not the error term. A 750 uV offset across a 10 MOhm feedback resistor is 75 pA of apparent photocurrent, which is 7.5 percent of a 1 nA signal, so the offset is the term that matters and it can be trimmed at one temperature. The 2.5 uV/C drift over 100 C is 250 uV, or 25 pA, which is the number that stays after trimming.

The 1 pA limit is specified over -40 to +125 C, which is the important detail. JFET bias current doubles roughly every 10 C, so a part specified at 1 pA at 25 C only would be a very different part at 85 C. Here the limit already covers the range, so a 10 MOhm source sees 10 uV of bias error at 125 C, not 1 uV.

The input window is not the supply range

On a 5 V supply the input common mode range is 0 V to +3 V, so the amplifier cannot follow a signal to 5 V even though it runs from a 5 V rail. On plus or minus 13 V the window is -13 V to +10 V, which asymmetric shape is worth reading twice: the negative end reaches the rail and the positive end stops 3 V below it. A 0 V to 10 V industrial signal on a plus or minus 13 V supply fits; a 0 V to 12 V signal does not.

The output swings to 4.95 V minimum on a 5 V supply, which is 50 mV short of the rail, so a converter reference of 4.096 V is a better use of the span than a 5 V reference. At 3 MHz of gain bandwidth the part is fast enough to be a transimpedance stage up to a few hundred kilohertz depending on the feedback capacitance.

Current and heat on a 24 V rail

250 uA per amplifier on a 26 V rail is 6.5 mW per channel, so a dual is 13 mW and the package does not notice. The 26 V rating is the useful part: a 24 V industrial bus with a 10 percent tolerance reaches 26.4 V, which is above the limit, so a 24 V board needs a clamp or a different part. On a 15 V rail the same amplifier has 11 V of headroom and no issue at all.

Sourcing notes for this family: medical device components holds the cross references, the obsolete part cross reference hub is the pre substitution check, and component lead time solutions is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask

Can the AD8642ARZ run from a single 5 V supply with a 0 V to 5 V signal? No. The input common mode range stops at +3 V on a 5 V supply, so the top 2 V of that signal is outside the part. Use a plus or minus 5 V supply and centre the signal, or attenuate it.

Is 750 uV of offset a problem for a photodiode stage? It is 75 pA across a 10 MOhm feedback resistor, which is a small fraction of a nanoamp signal but dominant for a picoamp signal. Trim it at the calibration temperature and budget the 2.5 uV/C drift afterwards.