Contact Us

AD8607ARMZ

Brand: Analog Devices
Analog Devices AD8607ARMZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8607ARMZ — Analog & Mixed-Signal ICs | Superb Automation

AD8607ARMZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8607ARMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8607ARMZ: dual micropower amplifier with 50 microvolts offset in MSOP-8

The AD8607ARMZ is the two channel member of the AD8603/AD8607/AD8609 family in an 8-lead MSOP: a 50 uV maximum offset, a 1 pA maximum bias current, 25 nV/root Hz of noise and 40 uA of supply current per amplifier from a 1.8 V rail. It is the low power end of the precision range, and the numbers it gives up are bandwidth and slew rate rather than accuracy.

Published values

ParameterValue
Offset voltage12 uV typical, 50 uV maximum
Offset voltage drift1 uV/C typical, 4.5 uV/C maximum
Input bias current0.2 pA typical, 1 pA maximum
Input voltage range0.3 V beyond both rails
Supply current, both channels80 uA typical, 100 uA maximum
Gain bandwidth400 kHz at 5 V, 385 kHz at 1.8 V
Slew rate0.1 V/us
Voltage noise density25 nV/root Hz at 1 kHz
Settling to 0.1%23 us on a 2 V step at unity gain
CMRR and PSRR80 dB minimum, 98 to 100 dB typical
Thermal resistance, MSOP-8142 C/W junction to ambient
Supply range1.8 V to 5 V single supply

The same accuracy as a 25 microvolt class part for a fortieth of the current

Measured on offset, drift and bias current, this amplifier sits in the same class as a 10 MHz low noise part: 50 uV against 65 uV, 4.5 uV/C against 4.5 uV/C, 1 pA against 1 pA. What it does not have is speed. At 0.1 V/us a 2 V step takes 20 us and the published settling is 23 us, so the usable signal bandwidth is around 4 kHz in a gain of 10 and 400 kHz at unity gain with a small signal. A circuit that needs the accuracy and not the speed saves 2 mA by choosing this part.

Noise against source impedance, not in isolation

Twenty-five nanovolts per root hertz looks high next to an 8 nV part, and it only matters if the source impedance is low. At 1 kOhm the resistor adds 4 nV and the total is 25.3 nV. At 100 kOhm the resistor adds 40 nV and the total is 47 nV, so the amplifier contributes a third of the noise power and the difference between a 25 nV and an 8 nV part is small. This is the calculation that decides between the two families for a bridge or a photodiode.

Two channels in a 3 mm body

The MSOP package is 3 mm by 3 mm with a 0.65 mm pitch, and at 142 C/W it runs cool: 100 uA at 5 V is half a milliwatt. In a battery instrument the two channels can therefore sit next to the sensor without a thermal gradient of their own, which matters when the sensor is a thermocouple and the cold junction is the board itself.

Where the part belongs

Portable gas and electrochemical sensors, thermopile and thermocouple channels, single cell medical monitors, and any two channel DC front end that has to run from 1.8 V. Above 10 kHz of signal, or where the channel has to be scanned quickly, the 10 MHz family is the correct answer and the current budget has to make room for it.

For a board that has to keep running while a reel runs out, medical device components is where the family alternatives sit, the amplifier cross reference is the check list before a substitute goes in, and how to verify a drop in replacement is how a gap is covered without a new line item.

Two questions buyers ask

Can the AD8607ARMZ be used at 1.8 V with a 1.8 V sensor output? Yes. The input range extends 0.3 V beyond both rails, so a sensor that sits at the positive rail can still be measured, and the offset specification does not degrade at 1.8 V.

What is the settling time for a full scale step? About 23 us to 0.1 percent on a 2 V step, which is set by the 0.1 V/us slew rate rather than by the loop.