Contact Us

AD8605ARTZ

Brand: Analog Devices
Analog Devices AD8605ARTZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8605ARTZ — Analog & Mixed-Signal ICs | Superb Automation

AD8605ARTZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8605ARTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8605ARTZ: single 10 MHz amplifier with 8 nanovolt noise in SOT-23-5

The AD8605ARTZ is a single CMOS rail-to-rail amplifier in a 5-lead SOT-23 that reaches 8 nV/root Hz of voltage noise and 10 MHz of gain bandwidth for 1 mA of supply current, with a 65 uV maximum offset and a 1 pA maximum input bias current. It is the part for a low level signal that also has to be fast, where a micropower amplifier would leave the noise floor too high and a bipolar input would load the source.

Published values

ParameterValue
Offset voltage, 3.5 V supply20 uV typical, 65 uV maximum at 3 V common mode
Offset voltage, 5 V rail-to-rail input80 uV typical, 300 uV maximum, 750 uV maximum over temperature
Offset voltage drift1 uV/C typical, 4.5 uV/C maximum
Input bias current0.2 pA typical, 1 pA maximum
Supply current1 mA typical, 1.2 mA maximum
Gain bandwidth10 MHz
Slew rate5 V/us
Voltage noise density8 nV/root Hz typical, 12 nV/root Hz maximum at 1 kHz
Output currentplus or minus 80 mA
Output at 10 mA load4.7 V minimum high, 210 mV maximum low on a 5 V rail
Input capacitance8.8 pF common mode, 2.6 pF differential
Supply range2.7 V to 5.5 V single supply

Eight nanovolts at one milliamp is the trade this part makes

A 25 nV amplifier at 40 uA and an 8 nV amplifier at 1 mA sit at opposite ends of the same curve, and the choice is made by the source impedance. A 1 kOhm source carries about 4 nV/root Hz of its own thermal noise, so the amplifier's 8 nV adds in quadrature to 9 nV and the total noise is 2.2 times the resistor alone. A 10 kOhm source carries 12.7 nV and the same amplifier adds only 5 nV in quadrature, which is why the low current part is not a compromise on a high impedance sensor.

The offset specification depends on where the input sits

Two offset lines are published. With a 3.5 V supply and the input at 3 V the maximum is 65 uV, which is the number on the front page. Across the full rail-to-rail input on a 5 V supply the maximum is 300 uV, and over temperature it is 750 uV. The difference is the crossover region of the input stage. A channel that measures a small signal within a volt of mid supply gets the tight number, and a channel that uses the whole input range does not.

Driving a capacitive load with 80 mA of output

The output sources and sinks 80 mA, so the part can drive a cable or a converter's sampling network directly, but the closed loop output impedance of 1 Ohm at 1 MHz is what sets the settling with a capacitive load. Above a few hundred picofarads the 1 Ohm and the load form a pole inside the loop and the 65 degree phase margin shrinks. A 50 Ohm series resistor at the connector is the usual fix.

Where the part belongs

Transimpedance stages for photodiodes with a few hundred kilohertz of bandwidth, active filters at 100 kHz with low noise, ADC drivers for 14 and 16 bit converters running at a few hundred kilo samples per second, and low noise reference buffers. Where the signal is below 10 kHz and the source impedance is high, the micropower parts in the same family give the same offset for a fortieth of the current.

The pages that answer this most often are the amplifier cross reference for the family alternatives, the ADC and DAC cross reference for the acceptance test, and component lead time solutions for the case where a replacement has to be fitted before the next build.

Two questions buyers ask

Is 8 nV/root Hz low enough for a 16-bit converter? For a 5 V, 16-bit converter one code is 76 uV. An 8 nV amplifier with a 20 kHz bandwidth contributes about 1.1 uV rms, which is well under a code, so the amplifier is not the limit at that bandwidth. At 1 MHz the same amplifier contributes 8 uV rms and the converter resolution is no longer reachable.

Can the output drive a 1 nF load? Not directly. Isolate it with a series resistor and take the feedback from the amplifier side, otherwise the phase margin falls far enough to ring.