Contact Us

AD8512ARZ

Brand: Analog Devices
Analog Devices AD8512ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8512ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8512ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8512ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8512ARZ: two JFET input amplifiers with 8 MHz and 20 volts per microsecond

The AD8512ARZ is the dual of the AD8510 family, in an 8-lead SOIC. Each amplifier has 25 pA of typical bias current, 8 MHz of gain bandwidth, 20 V per microsecond of slew rate and 2.3 mA of supply current. Offset is 0.9 mV maximum on the A grade, drift 1.7 microvolts per degree typical, noise 8 nV per root hertz and distortion 0.0005 percent. Where the single is used for a photodiode stage, the dual is used for the stage plus its buffer, or for a two pole active filter in one package.

Published values

ParameterValue
Configurationdual, 8-lead SOIC
Input bias current25 pA typical, 75 pA maximum at 25 degrees
Bias current at temperature0.7 nA at 85 degrees, 7.5 nA at 125
Input offset, A grade0.9 mV maximum at plus or minus 5 V, 1.8 over temperature
Offset drift1.7 microvolts per degree typical, 12 maximum
Gain bandwidth8 MHz per amplifier
Slew rate20 V per microsecond
Noise8 nV per root hertz at 1 kHz
Distortion0.0005 percent at 1 kHz, 2 kohm load
CMRR86 dB minimum
Supply current2.0 mA typical, 2.3 maximum per amplifier, 2.5 maximum over temperature
Output current40 mA typical per amplifier
Phase margin44.5 degrees
Supply rangeplus or minus 5 V to plus or minus 15 V

Two amplifiers in one package and the crosstalk that follows

Sharing a package means sharing a supply pin and a die, so the second channel sees the first one's load current through the supply impedance. At 8 MHz and 2 mA per amplifier, a shared 0.1 microfarad bypass is not enough; the datasheet calls for a local bypass at the package and a wider one on the rail.

The other shared path is thermal. Two amplifiers each dissipating 2.3 mA times 30 V is 138 mW in an 8-lead SOIC, so the die runs warmer than either channel alone and the offset drift of 1.7 microvolts per degree applies to that die temperature, not the ambient. A dual used as a two stage filter therefore has a slightly worse offset than the single.

Why a filter and its output buffer belong in one package

A 20 V per microsecond slew rate and 8 MHz of gain bandwidth are enough for a two pole Butterworth at 100 kHz with a 5 V swing, and the second amplifier buffers the filter output against the cable. The JFET input means the filter's resistor values, which are usually tens of kilohms, do not load the previous stage.

Where the dual falls short is in precision. The A grade's 0.9 mV offset and 12 microvolts per degree maximum drift are not a 16-bit dc specification. As an ac filter or a buffer the part is comfortable, and as a dc instrumentation amplifier the 0.4 mV B grade in the same family is the better buy.

What the JFET input does not fix

Low bias current does not mean low current noise. The current noise density is set by the gate leakage and rises with temperature, and at 125 degrees with a 1 Mohm source the 7.5 nA of bias current has a shot noise component that is larger than the 8 nV voltage noise divided by the impedance.

The input capacitance of 11.5 pF common mode and 12.5 pF differential is also part of the loop. At 8 MHz with a 10 kohm feedback resistor, the pole formed with the input capacitance is at 1.4 MHz, so the phase margin of 44.5 degrees degrades further and the circuit can ring even though the amplifier is unity gain stable on its own.

When an order code in this family cannot be found, the amplifier cross reference lists what else does the same job, the ADC and DAC cross reference covers what to check before a part is dropped into an existing board, and one stop BOM sourcing is the route we take on a live shortage.

Two questions buyers ask about the dual JFET amplifier

Can the two amplifiers run on different supplies? No. Both channels share the supply pins, so the rails are common. Where one channel has to swing further than the other, both must be run at the wider rail.

Is the B grade available in the dual? The order guide lists B grade codes for the single and the dual. The A grade code on this page is the one with 0.9 mV of offset.