AD8479ARZ-RL
Product Specifications
AD8479ARZ-RL
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8479ARZ-RL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8479ARZ-RL: plus or minus 600 V of common mode into a difference amplifier with a fixed gain of 1
The AD8479ARZ-RL is an Analog Devices difference amplifier that measures a differential signal sitting on a common mode voltage of up to plus or minus 600 V, with a fixed gain of 1 and a rail to rail output, in an 8-lead SOIC. Common mode rejection is 90 dB minimum, bandwidth is 310 kHz, supply current is 550 uA typical, gain nonlinearity is plus or minus 5 ppm maximum, offset drift is plus or minus 10 uV per degree C maximum and gain drift is plus or minus 5 ppm per degree C maximum. The inputs survive common mode and differential transients of plus or minus 600 V, supply range is plus or minus 2.5 V to plus or minus 18 V, and the part is specified from -40 C to +125 C. It replaces an isolation amplifier where galvanic isolation is not required. It is on the analog and mixed-signal IC line card.
90 dB of rejection at 600 V still leaves 19 mV of error
90 dB is a rejection ratio of 31,623, so 600 V of common mode appears as 19 mV at the input, which the fixed gain of 1 passes to the output. At 100 V of common mode the same ratio gives 3.2 mV, and at 300 V it gives 9.5 mV. A 100 mV shunt signal measured at the top of a 600 V bus is therefore read with a 19 percent error unless the common mode is measured and subtracted, or unless the amplifier is used in a ratiometric arrangement where the same common mode appears on both inputs. That is the honest statement of what a difference amplifier with this rejection can do.
| Parameter | Vendor figure | Derived figure |
|---|---|---|
| Common mode range | plus or minus 600 V | 1200 V span, protected against transients to the same level |
| CMRR | 90 dB minimum | 19 mV of error at 600 V, 3.2 mV at 100 V |
| Gain | fixed at 1 | no external resistors, so no ratio mismatch to trim |
| Offset drift | plus or minus 10 uV per degree C | 1.65 mV over the 165 degree industrial span |
| Gain drift | plus or minus 5 ppm per degree C | 825 ppm, 0.083 percent, over the same span |
| Bandwidth | 310 kHz | 31 kHz at a gain of 10 in the following stage |
| Supply and package | plus or minus 2.5 V to 18 V, 8-lead SOIC | 16.5 mW at plus or minus 15 V |
A fixed gain of 1 pushes the gain into the next stage, and that is deliberate
Because the differential stage has no external resistor network, the gain error and the common mode rejection do not depend on resistor matching, which is where a discrete difference amplifier loses its rejection above a few kilohertz. The gain is then applied by a following amplifier, whose own offset and drift add to the chain but whose resistor network is easy to keep matched. The split is the reason the part holds 90 dB at 310 kHz, where a four resistor difference amplifier built from a general purpose op amp would have lost most of its rejection.
Selection notes
- The 600 V rating is a continuous common mode range and a transient protection level, not a standoff rating, so the part does not replace an isolation barrier where safety isolation is required.
- The rail to rail output allows the full converter span to be used when the part runs from the same 5 V rail as the converter.
- The high side current sense application needs a supply that sits at the same potential as the common mode, or a floating supply, which is a system decision.
- The -EP version extends to -55 C with a DSCC drawing number for defence programmes.
Questions buyers ask
Can this replace an isolation amplifier? Only where galvanic isolation is not required. It measures a high common mode voltage with a resistive input network, and the barrier is not there.
Why is the bandwidth only 310 kHz? The input attenuator and the internal stage set it, and the part is aimed at dc and low frequency current sensing rather than at power quality analysis above the audio band.
Difference amplifiers are compared on amplifier cross reference, and the parts held for patient connected monitors are grouped under medical device components.
Request Quote — In Stock, 100% New & Original, Full Warranty