AD8422ARZ
Product Specifications
AD8422ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8422ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8422ARZ: 368 microamps of instrumentation amplifier
The AD8422ARZ is the A grade of a rail-to-rail output instrumentation amplifier that draws 368 microamps maximum, which is less than a sixth of the 2.3 mA of the low noise part next to it in this family. Input noise is 8 nV per root hertz maximum, bandwidth is 2.2 MHz at unity gain and 12 kHz at a gain of 1000, gain is 1 plus 19.8 kohm over RG from 1 to 1000, and the supply spans 4.6 V to 36 V single or plus or minus 2.3 V to plus or minus 18 V. It is the third generation of the AD620 line, in the AD8221 pinout.
Published values
| Parameter | Value |
|---|---|
| Supply current | 368 microamps maximum quiescent |
| Supply range | 4.6 V to 36 V single, plus or minus 2.3 V to plus or minus 18 V dual |
| Input noise | 8 nV per root hertz at 1 kHz, 0.15 microvolts peak to peak at a gain of 100 |
| Bandwidth | 2.2 MHz at a gain of 1, 120 kHz at 100, 12 kHz at 1000 |
| Slew rate | 0.8 V per microsecond |
| Settling to 0.01 percent | 13 microseconds at a gain of 1, 80 at a gain of 1000 |
| CMRR | 86 dB minimum at a gain of 1, 146 dB minimum at a gain of 1000 |
| Input offset, A grade | 60 microvolts maximum, 70 over -40 to +85 |
| Offset drift, A grade | 0.4 microvolts per degree maximum |
| Input bias current | 1 nA maximum, 2 nA over temperature |
| Gain equation | G equals 1 plus 19.8 kohm divided by RG, range 1 to 1000 |
| Nonlinearity | 0.5 ppm typical at a gain of 1 with a 2 kohm load |
| Reference input | 20 kohm, 35 to 50 microamps of bias |
| Package | 8-lead SOIC |
The slew rate is the price of the current budget
0.8 V per microsecond against 35 on the low noise part is a factor of forty, and it shows up as 13 microseconds of settling at unity gain against 0.7. A 4 V output step at 0.8 V per microsecond alone takes 5 microseconds, so the settling figure is dominated by the slew, not by the loop.
For a thermocouple or a pressure sensor sampled at 10 Hz that is irrelevant. For a multiplexed 100 kSPS front end it rules the part out, because 13 microseconds of settling per channel puts a ceiling of about 70 kSPS before the acquisition window is counted. Choosing between this and the 2.3 mA part is therefore a question of sample rate and battery life, not of accuracy.
Three hundred and sixty eight microamps buys a battery product
On a 3 V rail the part dissipates 1.1 mW, against 6.9 mW for the low noise part. Over a year that is 9.7 Wh against 60 Wh, which is the difference between a two cell pack that lasts and one that does not. A loop powered 4 to 20 mA transmitter has 4 mA total to spend and can afford this part where the other one would take more than half the budget.
The penalty is noise. 8 nV per root hertz over a 10 kHz band is 0.8 microvolts RMS, which is 5 LSB of a 16-bit converter on a 2.5 V reference. Over the 10 Hz band a temperature signal actually occupies it is 25 nV RMS, which is 0.16 LSB. The noise figure only matters against the bandwidth of the signal, and that is why a slow part with 8 nV can still be a 16-bit front end.
Rail-to-rail output, and the reference pin that is not a rail
The output swings to within tens of millivolts of either rail, which matters on a 3 V single supply where a 0.5 V to 2.5 V span is the whole dynamic range. The reference pin sets the output level and has a 20 kohm input resistance drawing 35 to 50 microamps, so it cannot be driven from a high impedance divider without buffering.
The input common mode is a separate limit. The CMRR is specified over plus or minus 10 V with a 1 kohm source imbalance, and the input range on a single 5 V supply does not reach the positive rail. A bridge with a 2.5 V common mode on a 5 V supply sits inside the range, and the same bridge on a 3 V supply needs the reference moved to keep it there.
For a board that has to keep running while a reel runs out, the amplifier cross reference is where the family alternatives sit, medical device components is the check list before a substitute goes in, and one stop BOM sourcing is how a gap is covered without a new line item.
Two questions buyers ask about the low power in-amp
Can this run from a single 3.3 V supply? No. The minimum single supply is 4.6 V, so a 3.3 V rail is outside the specification. The 5 V rail or a dual supply is the route, and a 3.3 V system needs a different part.
What is the maximum gain? 1000, set by 19.8 kohm over RG. At that gain the bandwidth is 12 kHz and the settling time to 0.01 percent is 80 microseconds.