AD8421ARZ
Product Specifications
AD8421ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8421ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8421ARZ: the same 3 nV in-amp in the SOIC body
The AD8421ARZ is the A grade of the AD8421 in the 8-lead SOIC. The electrical table is identical to the MSOP code: 3.2 nV per root hertz maximum input noise, 2.3 mA maximum supply current, 10 MHz at unity gain, 35 V per microsecond slew, 60 microvolts of input offset maximum and 0.4 microvolts per degree of drift. The choice between this and the MSOP is a board question rather than a performance one, and the SOIC is the body that most existing boards were laid out for.
Published values
| Parameter | Value |
|---|---|
| Supply range | plus or minus 2.5 V to plus or minus 18 V |
| Supply current | 2.3 mA maximum |
| Input voltage noise | 3.2 nV per root hertz at 1 kHz, 200 fA per root hertz current noise |
| Bandwidth | 10 MHz at unity gain, 2 MHz at a gain of 100 |
| Slew rate | 35 V per microsecond |
| Settling | 0.7 microsecond at a gain of 1 to 0.01 percent, 1 microsecond to 0.001 percent |
| CMRR | 86 dB minimum at a gain of 1, 126 dB minimum at a gain of 100 |
| Input offset | 60 microvolts maximum, 86 over -40 to +85 |
| Offset drift | 0.4 microvolts per degree maximum |
| Output offset | 350 microvolts maximum, 6 microvolts per degree |
| Input bias current | 1 nA maximum, 8 nA over temperature |
| Gain | 1 plus 9.9 kohm over RG, range 1 to 10,000 |
| Nonlinearity | 1 ppm at a gain of 1 with a 2 kohm load |
| Package | 8-lead SOIC |
Why a 1 ppm nonlinearity figure is worth reading twice
One part per million at a 10 V output swing is 10 microvolts, which at a gain of 1 is the same order as the 60 microvolt offset but does not scale with gain the way offset does. For a strain gauge bridge that spans 3 mV at full scale, the nonlinearity is 3 nV referred to the input and disappears under the noise; for a 10 V instrumentation channel it sets the distortion floor.
The load matters. The 1 ppm belongs to a 2 kohm load at a gain of 1, and the datasheet gives a different number with a lighter load. A part driving an ADC with a 10 kohm input resistance and a sample capacitor is not in that condition, so the distortion that appears in a fast acquisition system usually comes from the sampling charge, not from the amplifier's own linearity.
What the SOIC buys on a supply of plus or minus 15 V
At the top of the supply range the part dissipates 2.3 mA times 30 V, which is 69 mW, and that heat leaves through eight pins. The SOIC body has more lead frame area than the MSOP, so it runs a few degrees cooler, and at plus or minus 15 V with a 2 kohm load that can be the difference between a 95 degree board and a 100 degree board.
The temperature range is -40 to +85 for the offset and CMRR limits and the part is specified beyond that with relaxed numbers. In a rack that sits at 70 degrees internal the derating is small; in a sealed enclosure at 85 the 86 microvolt offset limit over temperature is the one that matters, not the 60 microvolt room figure.
The resistor that sets gain is part of the error budget
Gain is 1 plus 9.9 kohm divided by RG. At a gain of 10, RG is 1.1 kohm, and a 0.1 percent resistor gives 0.1 percent of gain error against the 0.2 percent of the A grade part. At a gain of 1000 the resistor is 9.9 ohms and its own temperature coefficient, typically 25 ppm per degree for a thin film part, contributes more drift than the amplifier's 1 ppm per degree gain drift.
That is the practical argument for buying a B grade only when the resistor has already been bought. A 0.02 percent gain error on the amplifier is meaningless beside a 0.1 percent resistor, so the grade premium is best spent on the input offset, which no external component can fix.
Two pages worth reading before a purchase order goes out are the amplifier cross reference and OEM procurement; the first lists what else fits the socket, the second is the test sequence for a drop in, and how to verify a drop in replacement covers the case where the shortage is already on the line.
Two questions buyers ask about the SOIC code
Can this replace an AD620 in an existing socket? The pinout follows the AD8221 high performance arrangement rather than the AD620, so it is not a drop in. The gain resistor is still a single resistor, but the pin numbers and the reference arrangement have to be checked.
Is 2.3 mA really the maximum? Yes, across the supply range and the temperature range. It is a maximum rather than a typical, which is unusual in this class and makes the supply budget easy to close.