AD8421ARMZ-R7
Product Specifications
AD8421ARMZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8421ARMZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8421ARMZ: the 3 nV instrumentation amplifier in an MSOP body
The AD8421ARMZ is the A grade of a low power instrumentation amplifier with 3.2 nV per root hertz of input voltage noise, 2.3 mA of maximum supply current and 10 MHz of bandwidth at unity gain. Gain is set by one resistor from 1 to 10,000 using the 9.9 kohm internal pair, the input stage survives 40 V from the opposite supply, and the part runs from plus or minus 2.5 V up to plus or minus 18 V, or 5 V to 36 V on a single rail. This order code is the 8-lead MSOP, which is the body to choose when the board space is tighter than the SOIC footprint.
Published values
| Parameter | Value |
|---|---|
| Supply range | plus or minus 2.5 V to plus or minus 18 V, or 5 V to 36 V single supply |
| Supply current | 2.3 mA maximum |
| Input voltage noise | 3.2 nV per root hertz maximum at 1 kHz |
| Current noise | 200 fA per root hertz at 1 kHz |
| Bandwidth | 10 MHz at a gain of 1, 2 MHz at a gain of 100, 0.2 MHz at 1000 |
| Settling to 0.001 percent | 1 microsecond at a gain of 1, 0.8 at 100, 6 at 1000 |
| Slew rate | 35 V per microsecond |
| CMRR | 86 dB minimum at a gain of 1, 94 typical; 136 dB minimum at a gain of 1000 |
| Input offset, A grade | 60 microvolts maximum, 86 over the -40 to +85 range |
| Offset drift, A grade | 0.4 microvolts per degree maximum |
| Input bias current | 1 nA maximum at 25 degrees, 8 nA over temperature |
| Gain equation | G equals 1 plus 9.9 kohm divided by RG, range 1 to 10,000 |
| Gain error | 0.02 percent at a gain of 1, 0.2 percent from 10 to 1000 |
| Input protection | 40 V from the opposite supply |
| Package | 8-lead MSOP |
Noise, bandwidth and current draw in one part
The three numbers that usually conflict on an instrumentation amplifier are noise, bandwidth and supply current, and this part puts 3.2 nV per root hertz, 10 MHz and 2.3 mA in the same body. A 1 kohm source at 300 K contributes 4.1 nV per root hertz on its own, so the amplifier stops dominating above about 600 ohms of source resistance and the resistor is the noise floor from there up.
At a gain of 100 the bandwidth is 2 MHz, which is far more than a 250 kSPS converter needs and is the reason the part settles in 0.8 microseconds to 0.001 percent at that gain. In a multiplexed front end the settling time, not the bandwidth, decides the sample rate: 0.8 microseconds of settling plus the acquisition window is what sets the channel to channel period.
The grade letter changes the offset, not the noise
The A grade is 60 microvolts of input offset maximum against 25 for the B grade, and 86 against 45 over the -40 to +85 range. Drift follows the same pattern at 0.4 against 0.2 microvolts per degree. Nothing in the noise, bandwidth or supply current table changes between the grades, so a circuit that is noise limited can use either and a circuit that is dc limited should read the grade column.
The offset that matters at the output is not the input offset alone. The output offset is specified separately at 350 microvolts for the A grade and 250 for the B, and it appears after the gain, so at a gain of 1 the two terms add and at a gain of 1000 the input term is multiplied by a thousand while the output term stays put. That is why a high gain channel cares about the input number and a unity gain buffer does not.
Forty volts of protection from the opposite rail
The input stage tolerates 40 V from the opposite supply, which on a plus or minus 15 V rail means an input can be driven far past either rail without damage. On a multiplexed front end where one channel is powered down or a transducer is unplugged, that is the difference between a field return and a nuisance trip.
The protection does not extend to the supply pins, and it does not make the inputs rail to rail. The common mode range has to be respected for the CMRR figures to hold, and the 86 dB minimum at a gain of 1 falls to 80 dB at 20 kHz because the input capacitance and the source imbalance start to matter at frequency.
When an order code in this family cannot be found, the amplifier cross reference lists what else does the same job, medical device components covers what to check before a part is dropped into an existing board, and component lead time solutions is the route we take on a live shortage.
Two questions buyers ask about the AD8421
Is the MSOP body a different die from the SOIC? No. Same die, same electrical table, different package. The MSOP dissipates less heat into the board, which matters only at the top of the supply range.
What gain resistor gives 100? 99 ohms, from the equation 9.9 kohm divided by 99 gives 100 and the gain is that plus one. A 0.1 percent resistor is worth buying at that ratio, because the gain error of the part is 0.2 percent.