AD825ARZ
Product Specifications
AD825ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD825ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD825ARZ: 41 MHz From a JFET Front End With 12 nV of Noise
The AD825ARZ is a general purpose high speed amplifier built on a JFET input stage, and the combination is what makes it interesting. A JFET input keeps the bias current in the picoamp region, so a high impedance source does not develop an offset across its own source resistance, while 41 MHz of minus 3 dB bandwidth and 80 ns of settling time keep the part fast enough for imaging and converter buffering. Input voltage noise is 12 nV per root hertz, distortion is minus 76 dB at 1 MHz, and the output drives 50 mA minimum into an unlimited capacitive load without a series resistor. The part comes in an 8-lead SOIC with the standard single amplifier pinout.
Published values
| Parameter | Value |
|---|---|
| Bandwidth | 41 MHz at minus 3 dB |
| Settling time | 80 ns |
| Input stage | JFET |
| Voltage noise | 12 nV per root hertz |
| Distortion | Minus 76 dB at 1 MHz |
| Output current | 50 mA minimum |
| Capacitive load | Unlimited |
| Phase reversal | None when the input is at the rail |
| Body | 8-lead SOIC |
Charge coupled devices and the bias current argument
The application list on the data sheet starts with charge coupled device output stages, and the reason is arithmetic. A CCD output node presents a small capacitance and a signal that has to be buffered before it travels across a board, and any bias current flowing into that node develops a voltage across the source impedance that appears as a level shift which changes with temperature. With a JFET input the bias current is small enough that the shift is negligible over the operating range, so the black level of the image does not drift as the board warms. The same argument applies to photodiode transimpedance stages and to sample and hold inputs, which is why the part keeps appearing in imaging assemblies built long after it was introduced.
Unlimited capacitive load and the 50 mA output
Two separate ratings combine here. The 50 mA minimum output current means the part can drive a 50 ohm load to a useful level or a 100 ohm twisted pair directly, and the unlimited capacitive load rating means the cable capacitance does not destabilise the loop. Together they remove the series resistor and the buffer stage that would otherwise sit between the amplifier and the connector on a video or instrumentation cable. The trade off is quiescent current, which rises with output stage size, so a battery powered instrument that only needs to drive a short trace is better served by a lower current part in the same family.
Where the settling figure is the deciding number
An 80 ns settling time is specified for a step, not for a small signal, and that distinction is what separates this part from amplifiers with higher bandwidth and slower settling. In a multiplexed acquisition channel the input to the buffer jumps when the multiplexer switches, and the buffer has to recover to converter resolution before the sampling switch opens. An amplifier with 100 MHz of bandwidth but a 300 ns settling tail will lose codes at the switch point while a slower part with a clean 80 ns settle will not. Reading the settling condition, including the step size and the tolerance, is the only way to compare two candidates honestly.
Sourcing an old but current high speed part
The AD825 has been in catalogs for a long time and it remains available, but the SOIC is the only body and that makes the part vulnerable to a single package supply interruption. When a build cannot wait, the alternatives are a family member with a different bandwidth and the same pinout, or a part from another vendor with an equivalent input structure. Neither is automatic: the input bias current and the output drive both change, and a photodiode front end is sensitive to the first while a cable driver is sensitive to the second. The amplifier cross reference page lists the JFET input high speed options we hold, the ADI part second source page shows grade and body equivalents, and the lead time page covers what can be pulled forward against a build date.