Contact Us

AD8226ARMZ-RL

Brand: Analog Devices
Analog Devices AD8226ARMZ-RL is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8226ARMZ-RL — Analog & Mixed-Signal ICs | Superb Automation

AD8226ARMZ-RL

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8226ARMZ-RL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

AD8226ARMZ-RL: An Instrumentation Amplifier that Runs from 2.2 V to 36 V

What this part is

The AD8226 is an instrumentation amplifier whose gain is set by one external resistor from 1 to 1,000, with a supply range of 2.2 V to 36 V single or plus and minus 1.35 V to plus and minus 18 V dual. The wide supply range is the point: the same order code works on a 3 V battery instrument and on a 24 V industrial loop, which is unusual in a low cost instrumentation amplifier and is what makes it a stock part rather than a catalogue entry for one market.

The input stage goes below the negative rail, so a small signal near ground can be amplified on a single supply without a negative rail, and the inputs are protected beyond the supplies: on plus and minus 5 V rails the part is guaranteed to withstand plus and minus 35 V at the input without damage. Minimum and maximum input bias currents are both specified, which is what allows an open wire to be detected on a sensor input. The body is an 8 lead small outline or an 8 lead MSOP, and the part is specified from minus 40 to plus 125 degrees C.

Published figures that matter to a buyer

Gain range1 to 1,000, set by one resistor
Supply, single2.2 V to 36 V
Supply, dualplus and minus 1.35 V to plus and minus 18 V
Bandwidth at a gain of 11.5 MHz
Common mode rejection at a gain of 190 dB minimum, BR grades
Input noise22 nanovolts per root hertz
Supply current350 microamps typical
Input rangebelow the negative rail
Input protectionplus and minus 35 V on plus and minus 5 V rails
Bias currentminimum and maximum both specified
Temperatureminus 40 to plus 125 degrees C

Where the headline numbers stop

The gain resistor is not optional at any gain above 1, and its tolerance is part of the gain error: for a gain of 10 the resistor is 5,489 ohm, for 100 it is 499 ohm and for 1,000 it is 49 ohm. At the top of the range a 1 percent resistor is a 1 percent gain error and the resistor, not the amplifier, becomes the specification. At a gain of 1 the resistor is omitted and the part is a difference amplifier with a 90 dB common mode rejection, which is a different job from a gain of 100 channel.

The 1.5 MHz of bandwidth is at a gain of 1 and falls with gain, so a channel at a gain of 100 has roughly 15 kHz of bandwidth, which sets the maximum signal frequency long before the converter does. The 22 nanovolts per root hertz is 0.696 microvolts rms over 1 kHz and 2.2 microvolts rms over 10 kHz, so a wideband channel pays for its bandwidth in noise.

Three hundred and fifty microamps at 5 V is 1.8 mW, which is why this part appears in multichannel industrial cards where sixteen channels have to run at once. The input protection of plus and minus 35 V on a plus and minus 5 V supply is seven times the rail, which is the figure that survives a field wiring fault rather than a bench mistake, and it is one of the reasons this part outlives cheaper amplifiers in process control.

Applications where it fits

  • Industrial process control input cards with bridge or thermocouple sensors.
  • Bridge amplifiers in weigh scales and pressure transmitters.
  • Medical instrumentation with a wide supply requirement.
  • Portable data acquisition that has to run from a single cell.
  • Multichannel systems where the channel count makes power per channel the deciding figure.

Two questions buyers ask

What is the difference from the AD8227? The AD8227 has the same package and a similar performance but its gain starts at 5 rather than at 1, so it is the part to use when the minimum gain is high and the gain of 1 case is not needed. A board that needs a gain of 1 cannot substitute the 8227, and the two are often confused because they appear next to each other in the same selection table.

Does the input go below the negative rail at every gain? The input range is a function of gain and of the common mode voltage, and the vendor publishes it as a diamond plot for exactly that reason. A channel that works at a gain of 1 can leave the valid region at a gain of 100, so the plot has to be read at the gain the channel will use rather than at the gain the data sheet headline quotes.

Sourcing notes and next step

AD8226ARMZ-RL is the 8 lead MSOP body on tape and reel, and the BR grade carries the tighter common mode rejection in the table above. The grade and the body are two separate fields in the order code, and a substitute that matches one and not the other is a different part. The amplifier cross reference page sets out the fields for an instrumentation amplifier substitution, the BOM shortage recovery page covers the route when the part is quoted long, and the analog and mixed signal IC family page lists the rest of the amplifier line.

Request Quote — In Stock, 100% New & Original, Full Warranty