AD8131ARZ
Product Specifications
AD8131ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8131ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8131ARZ: Fixed Gain of Two, 400 MHz, No External Resistors
The AD8131ARZ is a differential driver in an 8-lead SOIC with a gain fixed at two, set by trimmed resistors on the die. There is nothing to calculate and nothing to match: two 1.5 kohm resistors and two 750 ohm feedback resistors are inside the package, the input presents 1.5 kohm differentially to whatever drives it, and the output common-mode level is set by a voltage on the VOCM pin. Bandwidth is 400 MHz at full output, slew rate is 2000 V per microsecond, and the internal feedback holds output balance to minus 60 dB at 10 MHz, which is the number that keeps radiated emissions and even-order distortion down when the pair runs down a cable or into an ADC.
Published values
| Parameter | Value |
|---|---|
| Gain | 2 V/V fixed, internal resistors, no external parts |
| Bandwidth | 400 MHz, minus 3 dB, full power |
| Slew rate | 2000 V per microsecond |
| Output balance | minus 60 dB at 10 MHz |
| Distortion | 68 dB SFDR at 5 MHz into a 200 ohm differential load |
| Input offset voltage | 0.5 mV typical, 7 mV maximum |
| Supply | 2.7 V to 5 V single supply |
| Supply current | 11 mA typical quiescent |
| Input resistance | 1.5 kohm differential, from the internal network |
| Common-mode control | VOCM pin, separate from the signal path |
| Package | 8-lead SOIC |
The 1.5 kohm load is the first thing to budget
A fixed gain of two with internal resistors means the source sees 1.5 kohm differential, not a high impedance buffer input. On a 2 V peak to peak differential output the input signal is 1 V peak to peak, so the input current is about 0.67 mA peak, and that current has to come from the previous stage. A low distortion op amp with plenty of loop gain drives it without complaint. A passive filter, a long trace from a DAC output, or a sensor with a few kohm of source resistance will not, and the failure shows up as gain error and as second harmonic rather than as an obvious clipping. Where the source is weak, put a buffer in front or move to the AD8132, which sets gain with external resistors and leaves the input impedance to be chosen.
Where the 200 ohm distortion figure applies
The 68 dB of spurious free dynamic range is quoted into a 200 ohm differential load at 5 MHz. Loads lighter than that give better numbers, heavier loads give worse, and the datasheet curves show the trend. Video and ADC driving both sit comfortably above 200 ohm, so the quoted figure is representative. Cable driving does not: a terminated twisted pair presents 100 ohm differential, and the distortion and the output swing both fall away. For a 100 ohm line, the output level has to come down or the part has to run on 5 V rather than 3.3 V, because the swing limit is set by the supply and the internal resistor network, not by the load alone.
Setting the output common mode from one pin
The VOCM pin sets the average of the two outputs and draws almost no current, so it can be driven from a resistor divider, from a reference, or from the mid-rail of the ADC. Its bandwidth is deliberately limited, which is a feature: noise on that pin appears as common-mode signal and is largely rejected by the differential pair that follows. Bypass it with a capacitor to ground, and if the ADC has its own common-mode output pin, connect the two together rather than generating a second reference. Note that the input common mode and the output common mode are independent, which is what allows a single-ended ground-referenced signal to be shifted up to the 0.9 V or 1.5 V that a differential converter expects.
Availability and second sourcing
This is an older, low cost part and it goes short in cycles when video and instrumentation demand overlaps. The fixed internal network means a substitute is only acceptable if it also fixes gain at two with the same 1.5 kohm input and the same pinout, otherwise the surrounding filter and the ADC full scale both change. The amplifier cross reference page lists the parts that share this function, the pin to pin cross reference page covers the footprints that can be swapped without a board change, and the lead time page shows what is on the shelf for a build that ships this quarter.