Contact Us

AD8017ARZ

Brand: Analog Devices
Analog Devices AD8017ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8017ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8017ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8017ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8017ARZ: A Dual Line Driver That Puts 200 mA Into 25 Ohm

The AD8017ARZ is a dual high speed amplifier built for single supply digital subscriber line drivers. It delivers 10 V peak to peak single ended into a load while sourcing 200 mA into 25 ohm, or 20 V peak to peak differentially into 50 ohm, with a slew rate of 1,600 V per microsecond and an output that comes within 1.0 V of either rail. Each amplifier draws 7 mA of quiescent current, the package is an 8-lead SOIC with a thermal coastline pad, and the temperature range is commercial. The intended application is the customer premises end of an asymmetric digital subscriber line, where a low distortion driver has to work from a single 12 V rail and dissipate its own heat without a heatsink.

Published values

ParameterValue
ConfigurationDual amplifier, one package
Differential output20 V peak to peak into 50 ohm
Single ended output10 V peak to peak while delivering 200 mA into 25 ohm
Slew rate1,600 V per microsecond
Quiescent current7 mA per amplifier
Output swingWithin 1.0 V of either rail
DistortionLow, specified into a 10 ohm load on a 12 V supply
SupplySingle supply, 12 V nominal
Body8-lead SOIC with thermal coastline pad
Temperature rangeCommercial

One volt of headroom decides the rail

The output stops within 1.0 V of each rail, so a 12 V single supply gives a usable swing of about 10 V peak to peak, which is exactly the number in the headline specification. A 5 V rail would give 3 V peak to peak and would not drive a subscriber line at the required level, so the 12 V supply is not a preference but a requirement of the application. It also means the mid rail bias has to be clean: any ripple on the bias appears directly in the output because the amplifier has no negative rail to reject it against, and a 100 mV of bias noise is 100 mV of output noise on a signal that may be a few hundred millivolts.

Two hundred milliamps into 25 ohm and the heat that follows

Two hundred milliamps into 25 ohm is 1 W of load power per amplifier, and the amplifier dissipates the difference between the supply and the load voltage on top of its 7 mA of quiescent current. On a 12 V rail with a 2 V output, the pass stage drops 10 V at 200 mA, which is 2 W in the package for a fraction of the cycle, and that is why the part is offered in a thermal coastline SOIC and why the datasheet assumes a four layer board. The exposed pad is the only path to the copper, and a two layer board with the pad connected by a single trace will overheat long before the electrical limits are reached. Any replacement in this socket has to match the thermal path, not just the pinout.

Why the load is specified at 10 ohm

The distortion figure is quoted into a 10 ohm load on a 12 V supply, which is a harder load than the 25 ohm in the output current specification and reflects the transformer ratio seen by the line driver in a real modem. A driver that looks comfortable into 100 ohm and is then connected to a line transformer presenting 12 ohm will show distortion several orders of magnitude worse, because the output stage current has to rise and the drop across the internal stage grows with it. When comparing this part with a substitute, the load impedance and the supply voltage have to match the comparison, otherwise the numbers describe different circuits.

A dual driver for a differential line

The two amplifiers are used as the two halves of a differential drive, one inverting and one non-inverting, so the line sees twice the swing of a single ended stage and the even order distortion products cancel. That arrangement is why a dual part is used here rather than two singles: the matching between the halves sets the balance, and a part with poor matching radiates common mode noise onto the pair. A socket replacement must keep the same gain setting resistors in the same places, because the balance depends on the ratio rather than on the absolute value. The amplifier cross reference page groups the line driver parts by output current, the ADI part second source page covers the grades that are genuinely equivalent, and the component lead time solutions page shows what can ship against a production schedule.