AD7822BRZ
Product Specifications
AD7822BRZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7822BRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7822BRZ: Eight Bits in 420 Nanoseconds, With the Reference Already Inside
The AD7822 is the single channel member of a three part family that also includes the four channel AD7825 and the eight channel AD7829. It is an 8-bit half flash converter with a 420 nanosecond conversion time, a maximum throughput of 2 MSPS, an on-chip track and hold amplifier and an on-chip 2.5 V reference trimmed to 2 percent, in a 20-lead small outline body. The parallel port is 8 bits wide with an end of conversion pulse, so the part can drive a bus directly or run with a state machine that watches the pulse and never writes a control register.
Why 8 bits at 2 MSPS is a different product from 8 bits at 200 kSPS
Half flash means the conversion is done in two comparisons rather than a successive approximation loop, and that is what buys the 420 nanosecond conversion time. With 8 bits there are 256 codes, so on the 2 V peak to peak input span of the 3 V version one code is 7.8 mV, and on the 2.5 V peak to peak span of the 5 V version one code is 9.8 mV. An application that can live with 8 mV of quantisation, and many video, disk drive and subsampling receivers can, gets a converter that keeps up with a 2 MSPS stream without a pipeline and without a latency budget. The signal to noise ratio is specified for input frequencies up to 10 MHz, which is the honest way to describe a part used for subsampling: the track and hold keeps working well above the Nyquist frequency, so an intermediate frequency can be sampled directly.
VMID and the input span
The VMID pin sets the mid point of the input span, so the converter can be centred on a level other than half the supply. That is what makes the part usable behind an amplifier whose output sits at a fixed bias, and it is also what allows the input range to be adjusted rather than fixed at a supply derived value. The span itself follows the supply: 2 V peak to peak with a 3 V supply and 2.5 V peak to peak with a 5 V supply, both within 10 percent.
| Parameter | Value | What it decides |
|---|---|---|
| Architecture | 8-bit half flash | 420 ns conversion, no pipeline |
| Throughput | 2 MSPS maximum | 500 ns per sample including overhead |
| Channels | One single ended | The four and eight channel members share the family |
| Input span | 2 V peak to peak at 3 V, 2.5 V at 5 V | 7.8 mV and 9.8 mV per code |
| Span centre | Set by the VMID pin | Fits an amplifier with a fixed bias point |
| Reference | 2.5 V on chip, 2 percent tolerance | No external reference part required |
| Track and hold | On chip, specified to 10 MHz input | Direct subsampling of an intermediate frequency |
| Supply | 3 V or 5 V, both plus or minus 10 percent | Two defined operating points, not a range |
| Interface | 8-bit parallel port with an end of conversion pulse | Standalone operation without a controller |
| Power | Automatic power-down at the end of each conversion | Draw follows the actual sample rate |
| Package | 20-lead SOIC or TSSOP, 0.3 inch DIP also exists | Through hole and surface mount options |
The conversion start pin is also the power-down pin
Convert start and power-down share one input, so the part goes into its low power state at the end of every conversion and comes back when the next conversion is requested. That is a different behaviour from a converter with a standby register: the average current tracks the sample rate automatically, and a system that samples in bursts pays for the bursts rather than for the clock. The consequence for timing is that the first conversion after a long idle period has to include the wake up time, so a controller that assumes a fixed 420 nanoseconds on every conversion will be short by the wake up interval on the first one after an idle gap.
Where the part fits
Data acquisition systems and digital signal processor front ends, disk drive read channels, mobile communication receivers and subsampling applications are the named uses. It is also a sensible choice for a product that needs a fast wideband measurement at low resolution, such as an envelope detector or a peak catcher, where a 12-bit part at 1 MSPS would cost more and settle more slowly. A build that needs more channels in the same family should look at the AD7825 for four and the AD7829 for eight, which keep the 420 nanosecond conversion and the parallel port. For comparisons across converter families, the ADC and DAC cross reference page lists the pairs, the component lead time solutions page covers supply on parts of this class, and the BOM shortage recovery page covers alternatives when an allocation hits a production line.