AD7607BSTZ
Product Specifications
AD7607BSTZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7607BSTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7607BSTZ: Eight 14-Bit Channels Sampled at the Same Instant, and Why That Matters More Than 200 kSPS
The AD7607 is a complete data acquisition system on one die: eight analogue inputs, a 14-bit successive approximation converter, an on-chip 2.5 V reference with its buffer, a second order antialiasing filter in front of every channel and a 1 Mohm input buffer, all clocked from one 5 V analogue supply with a separate 2.3 V to 5.25 V VDRIVE for the logic side. It is a 64-lead LQFP. The headline throughput is 200 kSPS on all eight channels, which means the converter is not multiplexed: every channel has its own track and hold, so a conversion represents eight voltages taken at the same instant rather than eight voltages taken at eight instants 5 microseconds apart.
True bipolar inputs without a front end
Each input accepts plus or minus 10 V or plus or minus 5 V as a true bipolar signal on a single 5 V supply. That is the feature that removes parts from the BOM: a +/-10 V industrial signal normally needs an op amp stage to shift and attenuate it into a unipolar converter range, and that stage brings its own offset, drift and settling behaviour into the measurement. Here the resistor network inside the part does the scaling, and the 1 Mohm input impedance with clamp protection means a signal source sees a light load and a faulted input does not destroy the channel. The clamp protection and the 7 kV ESD rating are specified on the analogue inputs, so a field wiring error is a survivable event rather than a board replacement.
What 14 bits buys, measured rather than theoretical
An ideal 14-bit converter has a signal to noise and distortion ratio of 6.02 times 14 plus 1.76, which is 86.0 dB. The AD7607 is specified at 84 dB minimum and 84.5 dB typical on the plus or minus 10 V range and at 83.5 dB minimum and 85.5 dB typical on the plus or minus 5 V range, so the typical part is within 1.5 dB of the theoretical limit and the minimum part is 2 dB off it. Converting back, 84.5 dB is an effective number of bits of 13.7, and 83.5 dB is 13.6 bits. The integral nonlinearity and the differential nonlinearity are both plus or minus 0.25 LSB maximum, which is a tenth of the resolution, so linearity is not the limit at this resolution; noise is.
| Parameter | Value | What it decides |
|---|---|---|
| Channels | Eight, simultaneously sampled | Phase relationship between channels is preserved |
| Resolution | 14 bits | 20 V span divided into 16384 codes, 1.22 mV each |
| Throughput | 200 kSPS on all channels | Eight channels at 200 kSPS is 1.6 M results per second |
| Signal to noise and distortion | 84.5 dB typical at plus or minus 10 V | 13.7 effective bits, 1.5 dB short of the 14-bit ideal |
| Input ranges | Plus or minus 10 V and plus or minus 5 V | No external scaling amplifier for industrial signals |
| Input impedance | 1 Mohm with clamp protection | Light load on the source, survives a fault |
| Input filter | Second order antialiasing on every channel | Less out of band noise folded into the band |
| Reference | 2.5 V on chip with buffer | No external reference part in the BOM |
| Supply | 5 V analogue, 2.3 V to 5.25 V VDRIVE | 3.3 V logic without level shifters |
| Power | 100 mW at 200 kSPS, 25 mW in standby | 0.5 uJ per conversion cycle |
| Package | 64-lead LQFP | Eight channels in one footprint |
The oversampling pins and what they take away
Three logic inputs, OS2 through OS0, select an oversampling ratio inside the part, and the selection filters the conversion results digitally before they reach the output register. The trade is direct: the output rate falls by the oversampling ratio, so the 200 kSPS ceiling belongs to the no oversampling setting, and an oversampling ratio that improves the noise figure also lowers the rate at which new results appear. On a power line monitor that needs 50 Hz or 60 Hz rejection this is exactly the control that matters, because the filter can be positioned so the line frequency falls in a notch instead of being averaged downstream in software. On a control loop that needs 200 kSPS of fresh data, oversampling is not available.
Bus width and the reason parallel exists
Eight channels of 14 bits is 112 bits per conversion. At 200 kSPS that is 22.4 Mbit/s before any framing, register or padding overhead, which is why the part offers a parallel interface as well as the SPI, QSPI, MICROWIRE and DSP compatible serial port. A serial host that runs at 30 MHz has just enough clock to move the data if nothing else shares the bus, and a host that has to serve other peripherals will use the parallel port or reduce the rate. The pin compatible members of the family run from 14 bits to 18 bits, with the AD7606 at 16 bits and the AD7608 at 18 bits in the same outline, so a resolution upgrade does not necessarily disturb the board.
Applications where this arrangement pays are power line monitoring and protection, multiphase motor control, instrumentation and control systems, and multiaxis positioning, all of which need channels that are simultaneous rather than sequential. Where a build needs the 16-bit sibling or a second source for an existing socket, the ADC and DAC cross reference page lists the equivalents, and the component lead time solutions page covers allocation on parts of this class. For BOM level consolidation across several converter families, see the one stop BOM sourcing page.