AD603ARZ-REEL
Product Specifications
AD603ARZ-REEL
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD603ARZ-REEL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD603ARZ-REEL: 42 dB of gain across 1.05 V of control, with the bandwidth held to 90 MHz
The AD603ARZ-REEL is an Analog Devices variable gain amplifier for RF and IF automatic gain control, built around a seven stage R-2R attenuator followed by a fixed gain stage. Two pin selected ranges are offered: minus 11 dB to plus 31 dB with a 90 MHz bandwidth, and plus 9 dB to plus 51 dB with a 9 MHz bandwidth, and any intermediate range can be set with one external resistor. Gain is linear in decibels at 25 mV per dB, the control input is a 50 Mohm differential pair drawing 200 nA, and the gain settles within 1 us for a 40 dB step. Input noise density is 1.3 nV per root hertz, gain accuracy is plus or minus 0.5 dB typical, power is 125 mW at plus and minus 5 V, and the output drives a 100 ohm load with a specified distortion at 10 MHz. It is specified from -40 C to +85 C. It is on the analog and mixed-signal IC line card.
The attenuator sits in front of the amplifier, and that is why bandwidth does not move with gain
In a conventional variable gain stage the feedback network changes with gain, so the bandwidth moves with it. Here a 0 dB to minus 42.14 dB attenuator, built from seven taps spaced 6.021 dB apart and interpolated continuously, feeds a fixed gain amplifier. The amplifier never sees a large input and never changes its feedback, so the 90 MHz bandwidth belongs to the whole gain range. Forty two decibels of range at 25 mV per dB needs 1.05 V of control, which is why one volt of DAC output covers the central 40 dB.
| Parameter | Vendor figure | Derived figure |
|---|---|---|
| Gain range and bandwidth | minus 11 dB to plus 31 dB at 90 MHz | 42 dB of range in one pin option |
| Second option | plus 9 dB to plus 51 dB at 9 MHz | a decade of bandwidth traded for 20 dB |
| Control scaling | 25 mV per dB | 1.05 V spans 42 dB, 1 V spans the central 40 dB |
| Attenuator steps | 7 taps at 6.021 dB | 42.15 dB total, interpolated between taps |
| Noise density | 1.3 nV per root hertz | 12.3 uV rms over a 90 MHz band |
| Control input | 50 Mohm, 200 nA bias | a DAC can drive it without a buffer |
| Gain step settling | below 1 us for 40 dB | 1 V per microsecond of control slew |
| Power | 125 mW at plus and minus 5 V | 12.5 mA from a 10 V total rail |
| Input and load | 100 ohm input, drives 100 ohm | 10 mA of input current at 1 V rms |
Twelve microvolts of noise across the whole band, against a one volt signal
One and three tenths nanovolts per root hertz over 90 MHz is 12.3 uV rms, which against a 1 V rms output is 98 dB of signal to noise before the source is counted. The 100 ohm input resistance contributes 1.3 nV per root hertz of its own at room temperature, so the amplifier doubles the noise of a matched source and adds nothing to a 1 kohm one. That balance is what a front end engineer needs to know before choosing between this part and a discrete PIN diode attenuator.
Selection notes
- Several parts can be cascaded with their control offsets trimmed, which distributes the gain and keeps each stage's noise contribution low.
- The differential control input accepts single ended positive or negative drive, so a unipolar DAC output is enough.
- One external resistor between two pins selects an intermediate gain range, which is how a 30 MHz, 42 dB stage is built from the same part.
- Power of 125 mW at the recommended plus and minus 5 V is a fixed cost and does not fall at low gain, so a battery receiver has to budget for it.
Questions buyers ask
Is the gain really flat in dB? Yes, the control law is linear in decibels and calibrated, with plus or minus 0.5 dB typical accuracy, which is what makes a single DAC code map to a known gain.
Can two parts give 84 dB of range? Yes, cascaded with the control voltages offset so the second stage starts where the first runs out, at the cost of twice the noise and twice the 125 mW.
Variable gain and fixed gain amplifiers are compared on amplifier cross reference, and the sourcing options for a receiver build are on BOM shortage recovery.
Request Quote — In Stock, 100% New & Original, Full Warranty