Contact Us
  • Home
  • COMPONENTS
  • Draw Latches and Toggle Latches for Enclosure Doors

Draw Latches and Toggle Latches for Enclosure Doors

A draw latch pulls a door closed and holds it with an over centre action, so the clamping force and the keeper position are what decide the fit. The over centre latches here run from 135 N in the small size to 670 N in the medium heavy duty size, in steel, zinc plated steel and stainless. Pull action toggle latches cover 1600 to 8900 N, with a threaded U hook that takes up 9.1 to 24.6 mm of adjustment on the door. Latch and keeper are separate parts on the over centre range, so both are quoted together and both appear on the door drawing.
quote now

Product Specifications

Product Overview

A draw latch is a lever with a hook. The hook catches a keeper on the frame, the lever folds down, and the door is pulled into the frame and held there. The part that makes it work is the curved blade between the lever and the hook: it flexes as the lever goes over centre, so the latch keeps tension on the door instead of going slack the moment the lever is down. That flex is also what absorbs a gasket taking a set, a panel warming up in the sun, or a case going over a bump in a van.

The over centre range on this page is built around four sizes, and the clamping force is the figure that sorts them. The small size is 135 N, which is 30 lbf, and it suits a small instrument lid. The medium size comes in a light duty version at 310 N and a heavy duty version at 670 N, and the large size is 645 N on the 60 series. That spread matters because a latch that is too light springs open under a compressed gasket and a latch that is too heavy bows the door panel and puts a permanent set in the blade.

Material follows the environment rather than the force. Steel with a zinc plate and a bright chromate is the default for an indoor cabinet. The same body in steel with a black powder coat is the version for a front panel where the finish is visible. Stainless, passivated, is the version for a cabinet that sees wash down, salt air or a mast, and it costs more for the same force. On the small size the stainless body is 97-30-160-12 against the steel 97-30-160-11, and the two are otherwise the same part.

The keeper is the half of the latch that gets forgotten. On this range the latch and the keeper are ordered as two part numbers, and the keeper comes in concealed two hole, concealed one hole with a lug, single hole peg style, exposed single hole and exposed one hole with a lug. The choice is made by how the frame is built, not by the latch: a folded frame takes a concealed keeper, a flat frame takes an exposed one, and a peg style keeper is the one that lets a door drop onto the catch without a line of sight. The distance from the latch to the keeper is also the adjustment range, so the two have to be placed on the drawing together.

Mounting hardware is sized to the body. The small latch takes M3 (No. 4) round head screws or 3 mm (0.118 in) rivets, and the peg style keeper needs flat head screws so the peg sits flush. The medium latch takes M4 (No. 8) screws or 4 mm (0.156 in) rivets, and the large latch takes M5 (No. 10) screws or 5 mm (3/16 in) rivets. The medium and large bodies also carry a hole for a padlock and a smaller hole for a tamper evident seal, which is what turns a latch into a lockable closure without adding a second part.

Where the door has to be pulled hard rather than merely held, the page moves to a pull action toggle latch. These are the U hook clamps: a latch plate on the door, a threaded U hook on the frame, and a lever that pulls the plate in and locks over centre. The 323 holds 1600 N, the 331 holds 3200 N and the 341 holds 8900 N, with hook adjustment ranges of 9.1 mm, 22.1 mm and 24.6 mm. The threaded hook is the adjustment, so the door gap is taken up at the hook rather than with shims under the plate.

Two practice points are worth writing on the drawing. The first is tension setting: close the door ten times with the latch loose, then take up half a turn at a time until the gasket just touches, because a latch set tight on the bench bows the door once the gasket compresses. The second is the secondary catch. On a cabinet that travels, the spring loaded catch 97-58-101-11 in steel or 97-58-101-25 in stainless rides behind the lever and gives a second hold if the main lever is knocked open, and on a road case that part is cheaper than a replacement door.

Key Specifications

ParameterValueApplies to
Latch typeOver centre draw latch, pull action toggle latchAll parts
SizesSmall, medium, largeOver centre range
Clamping force, small135 N (30 lbf)97-30 series
Clamping force, medium310 N (70 lbf) light duty, 670 N (150 lbf) heavy duty97-50 series
Clamping force, large645 N (145 lbf)97-60 series
Holding capacity, toggle1600 N, 3200 N, 8900 N323, 331, 341
MaterialsStainless passivated, steel zinc plated, steel black powder coatBy part
Mounting screwsM3 (No. 4), M4 (No. 8), M5 (No. 10)By size
Mounting rivets3 mm (0.118 in), 4 mm (0.156 in), 5 mm (3/16 in)By size
Keeper stylesConcealed 2 hole, concealed 1 hole 1 lug, peg style, exposed 1 hole, exposed 1 hole 1 lugBy frame
Latch and keeperTwo part numbers, ordered separatelyOver centre range
Secondary catch97-58-101-11 steel, 97-58-101-25 stainlessAccessory
Padlock and seal holesPadlock bore 8.3 mm, seal bore 2.8 mmMedium and large body
Hook adjustment range9.1 mm, 19.3 mm, 22.1 mm, 24.6 mmToggle range
Toggle ratio27:1, 31:1, 32:1By model

Included Models and Order Codes

The rows below are the latches and keepers we quote most often. Size, force and material are given per part because those three figures decide whether the door closes, and a dash means the maker does not publish that figure.

Part NumberTypeSizeForceMaterialNotes
97-30-160-11Over centre latch, no keeperSmall135 N clampingSteel, zinc platedM3 screws or 3 mm rivets
97-30-160-12Over centre latch, no keeperSmall135 N clampingStainless, passivatedSame body as the steel part
97-37-103-11Concealed two hole keeperSmall-Steel, zinc platedPairs with 97-30 series
97-50-210-12Over centre latch, tab downMedium310 N clampingStainless, passivatedLight duty, M4 screws or 4 mm rivets
97-50-231-22Latch with concealed two hole keeperMedium310 N clampingStainless, passivatedSecondary catch ready
97-50-162-25Latch with single hole keeper and lugMedium670 N clampingSteel, black powder coatHeavy duty, tab up
97-60-120-11Over centre latch, tab downLarge645 N clampingSteel, zinc platedM5 screws or 5 mm rivets
97-60-320-11Over centre latch, no keeperLarge645 N clampingSteel, zinc plate, bright chromateKeeper ordered separately
97-58-101-11Spring loaded secondary catchMedium and large-SteelResists shock and accidental opening
323Pull action toggle latch1600 N1600 N holdingSteel, zinc platedU hook, 9.1 mm adjustment, 27:1
331Pull action toggle latch3200 N3200 N holdingSteel, zinc platedU hook, 22.1 mm adjustment, 32:1
341Pull action toggle latch8900 N8900 N holdingSteel, zinc platedU hook, 24.6 mm adjustment, 29:1

Key Features

Over centre blade holds tension – The curved blade flexes as the lever passes centre, so the latch keeps pulling on the door instead of going slack once it is closed.

Force stated per size – 135 N, 310 N, 670 N and 645 N are listed against the body size, so a gasket load and a door panel stiffness can be matched to one part.

Keeper chosen by the frame – Five keeper styles cover a folded frame, a flat frame and a door that has to drop onto the catch without a line of sight.

Stainless for wet and salt air – The passivated bodies carry the same force as the zinc plated parts, which is the version for wash down and masthead cabinets.

Secondary catch for travelling cases – The spring loaded catch rides behind the lever and holds the door if the main lever is knocked, which is cheaper than a replacement door.

U hook adjustment on the toggle range – 9.1 to 24.6 mm of threaded hook travel takes up the door gap at the hook rather than with shims under the plate.

Applications

These parts are used where a door, a lid or a cover has to be pulled against a gasket and held without a hinge-side bolt.

Instrument and control cabinets – A 310 N medium latch closes a door against a 3 mm gasket, and a concealed two hole keeper keeps the frame face flat for a wipe down.

Portable and road cases – A 645 N large latch with the 97-58-101-11 secondary catch holds a lid through transport and still opens with one hand.

Machine guards and moulds – A 331 toggle latch pulls a 3200 N load over centre and takes up 22.1 mm of gap on the threaded U hook.

A latch is picked by the gap between door and frame, so the keeper position is checked against the SUPERB PCB enclosure drawing before the door is punched. On the SUPERB PCBA route the latch is fitted after the door hardware is on, because a latch set against a door that still moves on its hinge is a latch that has to be re-drilled.

Sourcing and Cross-Reference

A latch is bought as a pair. The body and the keeper are two part numbers, and the distance between them is the adjustment that decides whether the gasket is compressed or crushed. When a latch is replaced on a door that already exists, the mounting hole pattern and the keeper style are the two things to match first, because a concealed two hole keeper will not drop into a frame that was punched for a peg style part.

The second point is force against the door. A 135 N latch on a lid with a light foam seal is right. The same latch on a door with a 4 mm gasket that has taken a set is a latch that pops open in a cold van. Going up a size is the simple fix, but the panel has to carry it: a 645 N body on a 1.5 mm door bows the door before it compresses the gasket. The ratio between the two is the figure worth checking before the door is punched.

The third point is the finish. Zinc plated steel is right indoors, powder coat is right where the latch is visible, and stainless is right where water and salt are. Mixing a stainless body with a zinc keeper is the one combination that shows up as rust on the frame two years later, so both halves are quoted in the same finish. We supply the latch, the keeper, the secondary catch and the mounting screws as one set, because a door that is waiting on one keeper is a door that is not shipping.

SUPERB Assembly closes the first door ten times with the latch set loose, then takes up the tension half a turn at a time, because an over-centre latch set tight on the bench pulls the door panel into a bow once the gasket takes a set.

Q: Can you supply a medium over centre latch with a concealed keeper for a door with a 3 mm gasket, and confirm the clamping force and the screw size?

A: Send the door thickness, the gap between door and frame at the latch and the pull the door has to hold. The SUPERB Tech desk quotes the latch with its keeper, because the two are ordered separately and a 135 N latch on a door with a compressed gasket is a latch that springs open on the first cold morning.

Why Buy Draw Latches and Toggle Latches Through SUPERB

  1. Force matched to the gasket: Clamping force is quoted against the door and the seal, which is where a 135 N latch gets ordered for a door with a 4 mm gasket.
  2. Keeper and body together: Both part numbers are quoted as a pair, so a door is not held up by a keeper that was left off the order.
  3. Material matched to the site: Zinc plated, powder coated and stainless bodies are on one page, so an indoor cabinet and a wash down cabinet do not share a finish.
  4. Toggle range for heavy pulls: The U hook clamps cover 1600 N to 8900 N with the hook adjustment stated, which is what a mould or a guard needs.
  5. Tension set at assembly: The first door is closed with the latch loose and taken up half a turn at a time, so the gasket is compressed rather than crushed.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Enclosure Handles and Corner Guards for Portable Units, Breather Vents and Pressure Equalization Plugs for Sealed Cases, Rocker and Toggle Switches for Equipment Panels, Mounting Brackets and DIN Rail Clips for Enclosures, Screw Terminal Blocks and Pluggable Connectors for Field Wiring, OEM Procurement.