Contact Us

TJA1057GT/1

Brand: NXP Semiconductors
NXP Semiconductors TJA1057GT/1 is a mcu & embedded component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TJA1057GT/1 — MCU & Embedded Processors | Superb Automation

TJA1057GT/1

NXP Semiconductors — MCU & Embedded Processors

Product Overview

The TJA1057GT/1 from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

TJA1057GT/1: SO8 CAN FD transceiver without a VIO pin

TJA1057GT/1 is the SO8 member of the TJA1057 line with the G variant timing and no VIO pin in the TJA1057 high speed CAN transceiver line, described by Rev 8 family document. It implements the third edition of ISO 11898-2 and is timed to 5 Mbit/s in the CAN FD fast phase, with a standby mode and a bus wake-up. The line is described as the choice for networks that only need basic CAN functionality, which is why it carries no INH output and no error pin.

Order code and package

Order codeTJA1057GT/1
Variant function on pin 5S input and STB input with standby mode; there is no VIO supply on this code
PackageSO8, 3.9 mm body width, 8 pins
ProtocolISO 11898-2:2024 third edition, SAE J2284-1 to SAE J2284-5 and SAE J1939-14
Maximum data rate1 Mbit/s on the TJA1057T code and 5 Mbit/s in the CAN FD fast phase on the other variants
Supply voltage on VCC4.5 to 5.5 V
Logic supply on VIO2.91 to 5.5 V on the variants that carry a VIO pin
Temperature rangeminus 40 to plus 150 C virtual junction
QualificationAEC-Q100
DatasheetRev 8 family document

Electrical parameters that decide the application

Bus fault voltageminus 58 to plus 58 V on CANH and CANL
Supply currentStandby current is in the microamp class with bus wake-up armed, and there is no INH output to switch a node regulator
Electrostatic discharge8 kV IEC 61000-4-2 and 8 kV human body model on the bus pins
Thermal resistance94 K/W junction to ambient in the SO8 body, 54 K/W for the HVSON8 body
Wake and diagnostic pinsS and STB inputs with standby and filtered bus wake-up, no INH and no error output
Bus pinsCANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one
Logic levelsdigital pins referenced to VCC, so a 3.3 V controller needs 5 V tolerant inputs
Behaviour with the supply offthe transceiver disengages from the bus so an unpowered node does not load the network
ProtectionTXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family
Ordering stringthe suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order

Points to check before this part goes on a BOM

The line is built for nodes that need a transceiver and not a power controller: there is no INH output to switch a regulator and no ERR output for diagnostics. A node that has to control its own supply belongs on the TJA1043 rather than here.

Timing is to the 2024 parameter sets, with a set A at 2 Mbit/s and a set B at 5 Mbit/s. A network specified against the 2016 text has to be mapped onto one of those sets before the part is chosen.

Digital pins sit at VCC on this code, so a 3.3 V controller depends on 5 V tolerant inputs and reads a 5 V RXD. The variants with a VIO pin remove that condition and are otherwise the same silicon.

Standby current is in the microamp class with bus wake-up armed, and the wake is filtered, so a short glitch on the bus does not wake the node. The filter is the same mechanism that rejects a wake pattern which is shorter than the standard requires.

The SO8 body is 94 K/W and the HVSON8 body is 54 K/W, so the 350 mW of a 70 mA dominant bus is a 33 C rise here and a 19 C rise there. The package choice is thermal and area, and it changes nothing in the protocol.

Bus pins stand minus 58 to plus 58 V and carry 8 kV on both the IEC 61000-4-2 and the human body model tests. The part is qualified to AEC-Q100 and specified for 12 V automotive systems, which is a narrower statement than the 24 V suitability of the TJA1042 and TJA1051 lines.

Where this order code fits

It is the part for a node that needs CAN FD and a standby wake but no supply control, and it is the usual cost down from the TJA1044 where the advanced low power features are not used. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the How to Reduce Component Cost page.

Questions buyers ask

Does TJA1057GT control the node supply? No. There is no INH output on this line. A node that has to switch its own regulator belongs on the TJA1043.

Can a 3.3 V controller use it directly? Only through 5 V tolerant pins, since the digital side sits at VCC. The variants with a VIO pin are the direct 3.3 V interface.

Is it a 24 V part? The document specifies it for 12 V automotive systems, while the bus pins stand plus or minus 58 V. A 24 V network should be checked against that statement rather than against the pin rating alone.

SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the Vendor Consolidation page sets out the checks that keep a substitute from failing on the bench.