TJA1057CT/0Z
Product Specifications
TJA1057CT/0Z
NXP Semiconductors — MCU & Embedded Processors
Product Overview
The TJA1057CT/0Z from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TJA1057CT/0Z: SO8 CAN FD transceiver with the shorter C variant delay
TJA1057CT/0Z is the SO8 member of the TJA1057 line with the shorter propagation delay of the C variant in the TJA1057 high speed CAN transceiver line, described by Rev 8 family document. It is the C variant of the TJA1057 line, which carries the shorter propagation delay that the family table associates with larger topologies. The physical layer, the standby mode and the bus ratings are the same as the other codes; the delay window is what changes.
Order code and package
| Order code | TJA1057CT/0Z |
| Variant function on pin 5 | S input and STB input with standby mode; no VIO supply on this code |
| Package | SO8, 3.9 mm body width, 8 pins |
| Protocol | ISO 11898-2:2024 third edition, SAE J2284-1 to SAE J2284-5 and SAE J1939-14 |
| Maximum data rate | 1 Mbit/s on the TJA1057T code and 5 Mbit/s in the CAN FD fast phase on the other variants |
| Supply voltage on VCC | 4.5 to 5.5 V |
| Logic supply on VIO | 2.91 to 5.5 V on the variants that carry a VIO pin |
| Temperature range | minus 40 to plus 150 C virtual junction |
| Qualification | AEC-Q100 |
| Datasheet | Rev 8 family document |
Electrical parameters that decide the application
| Bus fault voltage | minus 58 to plus 58 V on CANH and CANL |
| Supply current | Standby current is in the microamp class with bus wake-up armed, and there is no INH output to switch a node regulator |
| Electrostatic discharge | 8 kV IEC 61000-4-2 and 8 kV human body model on the bus pins |
| Thermal resistance | 94 K/W junction to ambient in the SO8 body |
| Wake and diagnostic pins | S and STB inputs with standby and filtered bus wake-up, no INH and no error output |
| Bus pins | CANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one |
| Logic levels | digital pins referenced to VCC, so a 3.3 V controller needs 5 V tolerant inputs |
| Behaviour with the supply off | the transceiver disengages from the bus so an unpowered node does not load the network |
| Protection | TXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family |
| Ordering string | the suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order |
Points to check before this part goes on a BOM
The C variant is one of the two codes with the shorter delay, alongside the B variant. On a network with long stubs or a high node count at 5 Mbit/s, that window is what decides whether the sample point still lands inside the bit.
The delay specification lists 62 ns typical and 90 ns maximum from TXD to bus dominant, with the recessive path at 75 ns typical and the low to low and high to high paths at 50 ns minimum. Those are the numbers a bit timing calculation has to absorb, and they are not the same as the G variant.
No VIO pin means the digital side is referenced to VCC. The document allows 3.3 V controllers on the non-VIO variants when the I/O are 5 V tolerant, which is a condition on the controller rather than a property of the transceiver.
Standby with bus wake-up is present, and the wake is filtered so that a short dominant pulse does not bring the node up. That filter is the reason a controller cannot use a truncated wake pattern as a fast path.
The SO8 body is 94 K/W. A 70 mA dominant bus at 5 V is 350 mW, a 33 C rise, and an 85 C ambient lands at 118 C against the 150 C limit, so the part has margin for the pull-ups and the leakage around it.
Bus pins stand minus 58 to plus 58 V with 8 kV IEC and 8 kV human body model, and the part is AEC-Q100 qualified and specified for 12 V automotive systems. A 24 V application should be checked against that specification statement, not against the 58 V pin rating.
Where this order code fits
It goes on 5 Mbit/s networks that have grown beyond a simple bus, where the shorter delay window buys margin at the far end and the rest of the line is enough. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
What does the C variant change? The propagation delay window, which is shorter than on the G variant and is what supports larger network topologies at 5 Mbit/s.
Is it pin compatible with TJA1057GT? Yes, both are SO8 with the same pin functions. The difference is the delay and the marking, and the digital side sits at VCC on both.
Does it have a VIO pin? No. The VIO variants carry a /3 in the ordering string, and those are the codes for a direct 3.3 V interface.
SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.