Contact Us

TJA1051T/3/1J

Brand: NXP Semiconductors
NXP Semiconductors TJA1051T/3/1J is a mcu & embedded component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TJA1051T/3/1J — MCU & Embedded Processors | Superb Automation

TJA1051T/3/1J

NXP Semiconductors — MCU & Embedded Processors

Product Overview

The TJA1051T/3/1J from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

TJA1051T/3/1J: SO8 CAN FD transceiver with a VIO pin

TJA1051T/3/1J is the SO8 member of the third generation line with a VIO pin on pin 5 in the TJA1051 third generation high speed CAN transceiver line, described by Rev 9 of 28 November 2017. It carries the ISO 11898-2:2016 physical layer and is timed for 5 Mbit/s in the CAN FD fast phase. The /3 suffix is the whole point of this code: pin 5 is a VIO supply, so the digital side follows a 3.3 V microcontroller without level shifting and without relying on 5 V tolerant inputs.

Order code and package

Order codeTJA1051T/3/1J
Variant function on pin 5VIO input on pin 5, which sets the digital interface level
PackageSO8, 3.9 mm body width, 8 pins
ProtocolISO 11898-2:2016 and SAE J2284-1 to SAE J2284-5
Maximum data rate5 Mbit/s in the CAN FD fast phase
Supply voltage on VCC4.5 to 5.5 V
Logic supply on VIO2.8 to 5.5 V on the /3 variants
Temperature rangeminus 40 to plus 150 C virtual junction
QualificationAEC-Q100
DatasheetRev 9 of 28 November 2017

Electrical parameters that decide the application

Bus fault voltageminus 58 to plus 58 V on CANH and CANL
Supply currentSilent mode 0.1 to 2.5 mA, normal recessive 2.5 to 10 mA and dominant 20 to 70 mA at 60 ohm
Electrostatic dischargeplus or minus 8 kV IEC 61000-4-2 at CANH and CANL
Thermal resistance155 K/W junction to ambient in the SO8 body, 55 K/W for the HVSON8 body of the same die
Wake and diagnostic pinsPin 5 is the variant selector: not connected, VIO on the /3 codes or EN on the /E code, and there is no standby mode
Bus pinsCANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one
Logic levelsTXD, RXD and S pins referenced to VIO, which accepts 2.8 to 5.5 V
Behaviour with the supply offthe transceiver disengages from the bus so an unpowered node does not load the network
ProtectionTXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family
Ordering stringthe suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order

Points to check before this part goes on a BOM

VIO is 2.8 to 5.5 V and its undervoltage detector trips between 1.3 and 2.7 V, which is a 1.4 V wide window. A 3.3 V rail at minus 10 percent is 2.97 V, safely above the top of that window, but a 2.5 V rail is inside it, so this is a 3.3 V and 5 V part and not a 2.5 V one.

VCC is 4.5 to 5.5 V with its own undervoltage detector between 3.5 and 4.5 V. The two detectors are independent, so a board that loses VCC while VIO stays up puts the part into a defined state instead of driving the bus from a dead supply.

Supply current is 0.1 to 2.5 mA in silent mode, 2.5 to 10 mA recessive and 20 to 70 mA dominant into 60 ohm. The dominant figure is the one that sizes the regulator: 70 mA at 5 V is 350 mW, and 155 K/W in the SO8 body turns that into a 54 C rise, so an 85 C ambient lands at 139 C against a 150 C limit.

The HVSON8 body of the same die is 55 K/W, which makes the same 350 mW a 19 C rise. That difference is the exposed pad and not the silicon, so it only exists if the pad is soldered to copper with vias, and a footprint copied without thermal vias gains nothing.

Loop delay from a TXD high to an RXD high is 40 to 250 ns and the low to low path is around 60 ns typical. The symmetry of those two numbers is what the 5 Mbit/s claim rests on, since a 5 Mbit/s bit is 200 ns and a 210 ns spread in one direction alone would swallow a whole bit.

There is no standby mode on this line. Pin 5 is VIO here and either not connected or an enable input on the other codes, so a node that has to wake from the bus belongs on the TJA1042 or TJA1043 instead, and swapping to this part silently removes the wake path.

Bus pins stand minus 58 to plus 58 V and carry plus or minus 8 kV IEC 61000-4-2. The 58 V window is the reason the part survives a 24 V jump start and a short to a 24 V rail, which the 27 V parts in the older generation do not.

Where this order code fits

It is the part chosen when the controller runs at 3.3 V and the network needs CAN FD, and when the node never sleeps deep enough to need a standby mode. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the Incoming Inspection Plan page.

Questions buyers ask

Does TJA1051T/3 work with a 3.3 V microcontroller? Yes. Pin 5 is a VIO supply and accepts 2.8 to 5.5 V, so the digital pins follow the 3.3 V rail without level shifting.

Can it replace a TJA1042 on an existing board? Only if the board does not use the standby mode. The two parts share the package and the bus pins, but the TJA1051 has no standby mode and its pin 5 is VIO rather than the standby input.

What is the thermal limit in the SO8 body? 155 K/W junction to ambient, which is a 54 C rise at the 350 mW a 70 mA dominant bus dissipates, so an 85 C ambient is inside the 150 C limit by 11 C.

SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the Vendor Consolidation page sets out the checks that keep a substitute from failing on the bench.