Contact Us

TJA1044GT/3

Brand: NXP Semiconductors
NXP Semiconductors TJA1044GT/3 is a mcu & embedded component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TJA1044GT/3 — MCU & Embedded Processors | Superb Automation

TJA1044GT/3

NXP Semiconductors — MCU & Embedded Processors

Product Overview

The TJA1044GT/3 from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

TJA1044GT/3: SO8 Mantis CAN FD transceiver with standby and a VIO pin

TJA1044GT/3 is the SO8 member of the Mantis line with a VIO pin and the 5 Mbit/s timing set in the TJA1044 Mantis high speed CAN transceiver line, described by Rev 8.0 of 6 November 2024. It carries the third edition of ISO 11898-2, published in 2024, and is timed for 5 Mbit/s in the CAN FD fast phase. The G variant is the one that keeps the wake receiver alive from VIO while VCC is shut down, which is the arrangement a body controller with a switched 5 V rail needs.

Order code and package

Order codeTJA1044GT/3
Variant function on pin 5VIO input on pin 5; STB selects standby with host and bus wake-up
PackageSO8, 3.9 mm body width, 8 pins
ProtocolISO 11898-2:2024 third edition, SAE J2284-1 to SAE J2284-5 and SAE J1939-14
Maximum data rate1 Mbit/s on the TJA1044T code and 5 Mbit/s in the CAN FD fast phase on every other variant
Supply voltage on VCC4.5 to 5.5 V
Logic supply on VIO2.91 to 5.5 V on the variants that carry a VIO pin
Temperature rangeminus 40 to plus 150 C virtual junction
QualificationAEC-Q100
DatasheetRev 8.0 of 6 November 2024

Electrical parameters that decide the application

Bus fault voltageminus 58 to plus 58 V on CANH and CANL
Supply currentStandby is a microamp class current with host and bus wake-up, and the VIO variants keep the wake receiver alive from VIO with VCC shut down
Electrostatic discharge8 kV IEC and 8 kV human body model on the bus pins
Thermal resistance94 K/W junction to ambient in the SO8 body, 54 K/W for the HVSON8 body
Wake and diagnostic pinsSTB input, host and bus wake-up, and a 0.5 to 1.8 s wake pattern filter on the C variant and on the VIO variants
Bus pinsCANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one
Logic levelsTXD, RXD and STB referenced to VIO, which accepts 2.91 to 5.5 V
Behaviour with the supply offthe transceiver disengages from the bus so an unpowered node does not load the network
ProtectionTXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family
Ordering stringthe suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order

Points to check before this part goes on a BOM

The document names ISO 11898-2:2024 rather than the 2016 revision, and the two are not the same parameter set: 2024 splits the CAN FD timing into a set A at 2 Mbit/s and a set B at 5 Mbit/s. A network specified against the 2016 text should be checked against the set that matches its data rate.

The wake receiver runs from VIO on the variants that carry a VIO pin, so VCC can be removed completely and the part still sees a wake pattern. That is different from a standby mode that keeps VCC alive at 10 microamps, and it is the reason this code appears on boards with a switched main rail.

The wake pattern filter is 0.5 to 1.8 s on the C variant and on the VIO variants, which meets both classical CAN and CAN FD pattern requirements. A controller that sends a short dominant pulse and expects a wake will be filtered out, and that is the first thing to check when a node does not wake.

VCC is 4.5 to 5.5 V and VIO 2.91 to 5.5 V, so a 3.3 V rail at minus 10 percent (2.97 V) is inside the VIO window with 60 mV of margin. A 3.0 V rail is not, and a 2.5 V rail is well outside it.

Propagation delay on the B and C variants is shorter than on the G variant, and the difference is what the larger topology claim rests on. This code carries the standard delay window, so a network with long stubs at 5 Mbit/s is where the B or C code is the better starting point.

The SO8 body is 94 K/W, so the 350 mW of a 70 mA dominant bus is a 33 C rise and an 85 C ambient lands at 118 C. The HVSON8 body of the same die is 54 K/W and lands at 104 C, and both figures assume the pad is soldered where there is one.

Where this order code fits

It is the part for a node with a switched 5 V rail that still has to wake on bus traffic, and it is the code most often quoted against the TJA1042 when a board is being refreshed to the 2024 standard. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Which ISO revision does TJA1044 implement? ISO 11898-2:2024 third edition, with timing split into a set A for 2 Mbit/s and a set B for 5 Mbit/s, alongside SAE J2284-1 to J2284-5 and J1939-14.

Does the wake receiver need VCC? Not on this code. The receiver runs from VIO so VCC can be switched off and the part still detects a wake pattern.

Is TJA1044T the same part at 5 Mbit/s? No. The TJA1044T code is specified to 1 Mbit/s only, and the loop delay symmetry parameters that the faster variants carry are not specified for it.

SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.