Contact Us

TJA1042TK/3/1J

Brand: NXP Semiconductors
NXP Semiconductors TJA1042TK/3/1J is a mcu & embedded component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TJA1042TK/3/1J — MCU & Embedded Processors | Superb Automation

TJA1042TK/3/1J

NXP Semiconductors — MCU & Embedded Processors

Product Overview

The TJA1042TK/3/1J from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

TJA1042TK/3/1J: HVSON8 CAN FD transceiver with standby and a VIO pin

TJA1042TK/3/1J is the leadless HVSON8 member of the standby line with a VIO pin in the TJA1042 high speed CAN transceiver line with standby mode, described by Rev 7 family document. It is the leadless version of the /3 code: same die, same 5 Mbit/s CAN FD interface, same standby mode, in a 3 x 3 mm body with an exposed pad. The reason to take it is thermal and board area, and the reason not to is assembly.

Order code and package

Order codeTJA1042TK/3/1J
Variant function on pin 5VIO input on pin 5 in the 3 x 3 mm leadless body
PackageHVSON8, 3 x 3 mm leadless, 0.85 mm tall, 8 pins
ProtocolISO 11898-2:2016, SAE J2284-1 to SAE J2284-5 and SAE J1939-14
Maximum data rate5 Mbit/s in the CAN FD fast phase, with shorter propagation delay on the B and C variants
Supply voltage on VCC4.5 to 5.5 V
Logic supply on VIO2.8 to 5.5 V on the /3 variants
Temperature rangeminus 40 to plus 150 C virtual junction
QualificationAEC-Q100
DatasheetRev 7 family document

Electrical parameters that decide the application

Bus fault voltageminus 58 to plus 58 V on CANH and CANL
Supply currentStandby 10 to 15 microamps on VCC and 5 to 14 microamps on VIO, normal recessive 2.5 to 10 mA and dominant 20 to 70 mA
Electrostatic dischargeplus or minus 8 kV IEC 61000-4-2 at CANH and CANL
Thermal resistance53 K/W junction to ambient, 14 K/W junction to case and 6 K/W junction to top of package
Wake and diagnostic pinsSTB input selects standby with bus wake-up, pin 5 is SPLIT on the plain codes and VIO on the /3 codes
Bus pinsCANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one
Logic levelsTXD, RXD and STB referenced to VIO, which accepts 2.8 to 5.5 V
Behaviour with the supply offthe transceiver disengages from the bus so an unpowered node does not load the network
ProtectionTXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family
Ordering stringthe suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order

Points to check before this part goes on a BOM

Junction to ambient drops from 92 K/W in the SO8 body to 53 K/W here, and the junction to case figure is 14 K/W with 6 K/W to the top of the package. Those numbers only exist once the exposed pad is soldered to copper with a via field, so a footprint copied without thermal vias keeps the die and loses the rating.

At 70 mA dominant and 5 V the part dissipates 350 mW, which is 18.6 K at 53 K/W against 32 K in the SO8 body. In an 85 C ambient that is 104 C against 117 C, and the 13 K difference is what lets a regulator sit closer on a small board.

The leadless body is 3 x 3 mm against 3.9 mm of body width plus leads, which is roughly a third of the board area. On a module where the transceiver shares space with a current sense resistor and a regulator, that is the argument, and it has nothing to do with electrical performance.

Inspection changes with the package. The leadless body needs automated optical inspection capability that the document names as a feature, and a house without that capability should stay on the SO8 code rather than add X-ray to every build.

Standby current is 10 to 15 microamps on VCC and 5 to 14 microamps on VIO, unchanged from the wired body, and the wake pattern is the same ISO 11898-2:2016 pattern with the 0.8 ms per phase time-out.

Bus pins stand minus 58 to plus 58 V with plus or minus 8 kV IEC 61000-4-2, and the exposed pad is not a bus pin, so a short from the pad to a rail is a board fault rather than a rated condition.

Where this order code fits

It goes on dense modules where board area and junction temperature both matter, and where the assembly house can inspect a leadless body. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the Incoming Inspection Plan page.

Questions buyers ask

Is TJA1042TK/3 the same die as the SO8 part? Yes. The difference is the body and the thermal path: 53 K/W against 92 K/W, in a 3 x 3 mm leadless package.

Does the exposed pad have to be soldered? Yes. The 53 K/W figure belongs to a soldered pad with a via field. Without it the part runs at the thermal resistance of the plastic and the package advantage disappears.

Can it be used with a 3.3 V controller? Yes. Pin 5 is a VIO supply that accepts 2.8 to 5.5 V, so the digital pins follow the 3.3 V rail.

SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.