Contact Us

TJA1028T/5V0/10

Brand: NXP Semiconductors
NXP Semiconductors TJA1028T/5V0/10 is a mcu & embedded component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TJA1028T/5V0/10 — MCU & Embedded Processors | Superb Automation

TJA1028T/5V0/10

NXP Semiconductors — MCU & Embedded Processors

Product Overview

The TJA1028T/5V0/10 from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

TJA1028T/5V0/10: SO8 LIN transceiver with a 5 V regulator at 10.4 kBd

TJA1028T/5V0/10 is the SO8 LIN transceiver with an integrated 5 V regulator and the low 10.4 kBd slope in the TJA1028 LIN transceiver with integrated voltage regulator, described by Rev 5 of 30 January 2023. It is the SAE J2602 member of the TJA1028 line: same 5 V 70 mA regulator, same LIN interface, with the output slope set for 10.4 kBd. The lower edge rate is the whole point, and it costs nothing in the parts count.

Order code and package

Order codeTJA1028T/5V0/10
Variant function on pin 5SLP_N input with an INH output; the 5V0 field is the regulator output and the 10 field is the low slope
PackageSO8, 3.9 mm body width, 8 pins
ProtocolLIN 2.0, 2.1, 2.2, SAE J2602 and ISO 17987-4:2016 (12 V) on the A to D codes
Maximum data rate20 kBd on the /20 codes and 10.4 kBd on the /10 codes
Supply voltage on VCC5.5 to 28 V on VBAT
Logic supply on VIOthe regulator itself delivers 5.0 V or 3.3 V at up to 70 mA with 2 percent accuracy
Temperature rangeminus 40 to plus 150 C virtual junction
QualificationAEC-Q100
DatasheetRev 5 of 30 January 2023

Electrical parameters that decide the application

Bus fault voltageminus 40 to plus 40 V on LIN and VBAT as a limiting value
Supply currentStandby 45 microamps typical and sleep 12 microamps typical with LIN wake-up still armed
Electrostatic dischargeplus or minus 8 kV IEC 61000-4-2 on LIN and VBAT
Thermal resistance88 K/W junction to ambient in the SO8 body
Wake and diagnostic pinsSLP_N input, INH output, LIN bus wake-up, regulator undervoltage detection with a reset output, and thermal protection
Bus pinsCANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one
Logic levelslogic pins compatible with the regulator output and with 3.3 V and 5 V controllers
Behaviour with the supply offthe transceiver disengages from the bus so an unpowered node does not load the network
ProtectionTXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family
Ordering stringthe suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order

Points to check before this part goes on a BOM

The 10.4 kBd setting is the SAE J2602 requirement, and it exists to limit the emission of a single wire bus that runs through a harness with no shield. A /20 part on the same network works and fails the emission test, which is the failure that costs a board respin rather than a component change.

The regulator is a 5 V low dropout block rated 70 mA at 2 percent accuracy, with undervoltage detection and a reset output. That is the same block as the /20 code, and the thermal arithmetic is the same: 490 mW and a 43 C rise at 12 V in, 910 mW and 80 C at 18 V in.

Standby is 45 microamps typical and sleep is 12 microamps typical, with LIN wake-up armed in sleep. A node that never enters sleep spends 394 mAh a year, so the firmware has to put it there.

The part carries plus or minus 8 kV IEC 61000-4-2 on LIN and VBAT and ISO 7637 transient protection on the same pins, which is the higher of the two ESD classes in this family and matches a module mounted in the harness.

Lin wake-up and the K-line compatibility of the underlying transceiver are both present, so the same part can serve a diagnostic K-line node without a second device. That compatibility is a line level feature and not a code level one.

The trailing digit of the ordering string that appears on some reel labels is the packing suffix. TJA1028T/5V0/10 and TJA1028T/5V0/10 with a packing suffix are the same electrical part, and a purchase order should quote the slash fields that carry the regulator voltage and the slope.

Where this order code fits

It is the part for J2602 sensor and actuator nodes that need their own 5 V rail, and it is the code to quote when a network has already failed an emission test on a faster slope. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the Supplier Quality Audit page.

Questions buyers ask

What is the difference between the /10 and /20 codes? The LIN output slope. /10 is 10.4 kBd for SAE J2602, /20 is 20 kBd. The regulator, the body and every other rating are identical.

Can it supply a microcontroller and a few LEDs? Yes, within 70 mA at 5 V and within the thermal budget: 490 mW at 12 V in is a 128 C junction in an 85 C ambient.

Is it the same regulator as the 3.3 V codes? Yes. The regulator is the same block with a different set output, so the accuracy and the 70 mA rating carry across the 3.3 V and 5 V versions.

SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.