Contact Us

UCC5350MCDWVR

Brand: Texas Instruments
Texas Instruments UCC5350MCDWVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC5350MCDWVR — Power Management & Signal Chain | Superb Automation

UCC5350MCDWVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC5350MCDWVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC5350MCDWVR: a single channel isolated gate driver with 10 A of peak output, an active Miller clamp and a 5 kVRMS barrier, in the eight pin wide body SOIC on a 1000 piece reel

UCC5350MCDWVR is an isolated driver for a silicon carbide, silicon or IGBT switch whose gate has to be held off during a fast drain transient, using a clamp transistor inside the driver instead of a negative supply rail in a SOIC body of 8 pins. The DWV body is the eight pin SOIC stretched to 8.5 mm of creepage, and the M suffix is the version with a Miller clamp, which is the reason a board can drop its negative bias supply and keep the FET off through a 50 V per nanosecond drain edge.

Order code and package

Catalogue stringUCC5350MCDWVR, where M is the Miller clamp version, C the 12 V output lockout, DWV the wide body eight pin SOIC and R the large reel
BodySOIC, DWV, eight pins with 8.5 mm of creepage across the barrier; the same die in the narrow D body has 4 mm of creepage and a 3 kVRMS rating instead of 5 kVRMS
Reelthe tape and reel table lists 1000 pieces for UCC5350MCDWVR, against 2500 for the narrow D body, so the wide body reel is the smaller of the two
Finish and moisturethe reel row prints Call TI against the finish and level 2 at 260 C with one year of floor life against moisture, while the non reel row lists NIPDAU
Temperatureminus 40 to 125 C, with the electrical table specified over that range rather than at 25 C only
Marking5350MC on the body, which does not distinguish the reel size and does identify the clamp version
Sibling rowsthe .A row of the same string is marked Obsolete, so the plain string is the one to buy and the suffix to avoid
DocumentSLLSER8J, June 2017, revised August 2024, covering the whole UCC53x0 family
StatusActive and in production on the addendum dated 10 September 2026

Electrical parameters that decide the application

Isolation5 kVRMS for one minute per UL 1577 in the DWV body, 7000 VPK per DIN V VDE V 0884-11, and a barrier life quoted above 40 years
Output current5 A minimum and 10 A typical source, 5 A minimum and 10 A typical sink, which is what moves a 500 nC gate in under 100 ns
Driver supplyup to 33 V on the output side, so 15 V positive and minus 5 V on the emitter fit with room to spare
Input supply3 V to 15 V on the input side, with a lockout that rises at 2.6 V to 2.8 V and falls at 2.4 V to 2.5 V with 0.1 V of hysteresis
Output lockout12 V version rising at 12 V minimum and 13 V typical, falling at 10.3 V to 11 V, with 1 V of hysteresis, so an IGBT sees a defined gate voltage before the driver starts switching
Propagation delay60 ns typical and 75 ns maximum in both directions, with 1 ns to 20 ns of pulse width distortion and 12 ns rise against 10 ns fall into 1 nF
Miller clampa clamp threshold of 2.1 V to 2.3 V, a clamp level of 26 mV to 50 mV at 20 mA, and 5 A to 10 A of clamp current for the first part of the edge
Input thresholds0.55 to 0.7 times the input supply for a rising edge and 0.3 to 0.45 times for a falling edge, with 0.1 times of hysteresis, so a 3.3 V logic signal has about 1.2 V of margin either side
Common mode immunity100 kV per microsecond minimum, which is the figure that decides whether a 600 V switching node produces output glitches
Quiescent current1.67 mA to 2.4 mA on the input side and 1.1 mA to 1.8 mA on the output side, both small compared with the gate charge
Thermal109.5 C per W junction to ambient in the narrow D body and 119.8 C per W in the DWV body, because the stretched package has less copper under it

Family options and how they differ

The M suffix, the part on this pageMiller clamp, 10 A source and sink, 12 V output lockout, for a silicon carbide or IGBT switch that needs the gate held off during a fast drain edge
The S suffixsplit output with separate turn on and turn off paths, which is the option when the two edges have to be tuned independently rather than clamped
The E suffixthe output lockout referenced to the emitter rather than to the output supply ground, which gives a true reading when the emitter moves
UCC5350SB8.5 A source and 10 A sink with an 8 V lockout, the member to choose when the bias rail is 12 V and the switch is a logic level FET
UCC5390 in the same family17 A source and sink, for a module with a gate charge above 1 uC where 10 A gives an edge that is too slow
The narrow D body4 mm of creepage and 3 kVRMS instead of 8.5 mm and 5 kVRMS, which is a functional or basic rating for a low voltage application and not a substitute for the wide body in a mains product

Points to check before this part goes on a BOM

The Miller clamp is a transistor, not a resistor, and that is why it works. A gate resistor holds the gate at the driver's output impedance, which for a 10 A driver is a few ohms, and a drain transient that pushes a nanoamp per picofarad of Miller capacitance through that impedance produces a voltage at the gate. The clamp is a switch from the gate to the emitter with 26 mV to 50 mV of drop at 20 mA and 5 A to 10 A of peak current, so the gate is shorted to the emitter rather than held through a resistor. The clamp threshold of 2.1 V to 2.3 V is the point at which the clamp releases, which means the clamp only takes over once the gate has already fallen below the threshold where the switch could conduct.

The wide body is bought for creepage and paid for in thermal resistance. 8.5 mm of creepage is what a mains product needs across the barrier, and the DWV body delivers it in the same eight pin outline as a narrow body. The cost is in the thermal number: 119.8 C per W instead of 109.5 C per W, because the stretched moulding has less copper bonded to it. At 200 mW of dissipation that is 24 C of rise against 22 C, which is small, and at 500 mW it is 60 C against 55 C, which is the point where the ambient derating has to be recalculated rather than copied from a previous board.

The reel size is the detail that breaks a production plan. The tape and reel table lists 1000 pieces for this string and 2500 for the narrow body, so a line that plans on 2500 per reel will find the wide body arrives in a reel it cannot load on the same feeder setup. A first article build of 200 pieces also needs a partial reel or a cut tape, and a distributor that quotes from a catalogue will often quote the narrow body figure because it is the one printed in the same row block.

The 12 V output lockout is the number that decides whether an IGBT is driven properly. A 15 V rail with a diode drop and a long trace sits near 14 V at the driver, which is inside the lockout window, and a rail that sags to 12 V under load is at the typical rising threshold. The part will start at 13 V and hold until 11 V, so a rail that sags below 11 V during a heavy transient drops the driver into lockout in the middle of a switching cycle. The result is a bridge that stops for a few microseconds and restarts, which looks like a controller fault and is really a bias rail that is too soft.

Dissipation is set by gate charge and switching frequency, and the clamp adds almost nothing. A 500 nC gate at 20 kHz and 15 V is 150 mW of gate charge, which in a 119.8 C per W body is 18 C of rise, and the quiescent current adds 27 mW. At 100 kHz the same gate is 750 mW and 90 C of rise, which is outside the package unless the ambient is cold. The arithmetic is the reason a 17 A member of the family exists rather than a bigger heat sink: a stronger driver shortens the edge and moves the loss into the switch, where the copper is.

When a clamp replaces a negative bias supply

A negative gate rail is the traditional answer to Miller turn on: hold the gate at minus 5 V so the threshold has to be crossed from further away. It works and it costs a second winding, a second regulator and a second set of capacitors on every channel. The clamp is the cheaper answer for the same problem, because it does not need a negative rail at all and it acts only during the edge that matters, when the drain is moving and the Miller current is flowing. Where the negative rail still wins is a module whose gate threshold is low and whose dv/dt is extreme, because a clamp holds the gate at zero and a threshold of 1.5 V is only 1.5 V away from zero, while a negative rail puts it 6.5 V away.

The clamp also has a second use that is easy to miss. During a short circuit the driver is asked to turn the switch off into a very high current, and the gate voltage can be pushed back up by the Miller current for as long as the drain moves. The clamp holds the gate down through that event, which is the difference between a switch that survives a short and one that fails. A board that relies on a gate resistor alone for turn off will fail the short circuit test at the second or third attempt, and the fix is a clamp rather than a larger resistor.

What the 5 kVRMS and 7000 VPK figures mean for a product

The 5 kVRMS withstand is the UL 1577 test at one minute, and it is the number a production hipot is set from. 7000 VPK is the transient rating under the German isolation standard, and it describes a surge event of microsecond duration rather than a continuous stress. The working voltage is what the standard sets separately, and in this body it is the figure that a safety reviewer compares against the continuous voltage the application applies across the barrier.

The practical consequence is that a 400 V motor drive with a floating high side is comfortably inside the rating, and a 690 V drive is at the edge of the working voltage rather than at the edge of the withstand. A product that quotes 5 kVRMS in its datasheet and runs the barrier at 1000 V continuously is making a claim about a test rather than about a life, and the two are not the same number.

Where this order code fits

This is the gate driver for a silicon carbide or IGBT switch in a motor drive, a solar inverter, a battery charger or an uninterruptible supply, where the gate has to stay off while the drain moves at tens of volts per nanosecond Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

What does the clamp do that a gate resistor does not? It shorts the gate to the emitter with a low impedance switch, 26 mV to 50 mV at 20 mA, so Miller current cannot lift the gate. A resistor holds the gate through a few ohms and lets the voltage rise.

Does it need a negative gate supply? No for most applications, because the clamp holds the gate at zero. A switch with a very low threshold and an extreme dv/dt is the case where a negative rail is still the safer choice.

How much current can it source and sink? 5 A minimum and 10 A typical in both directions, which is enough for a 500 nC gate in under 100 ns.

Why does the wide body reel hold fewer parts? The tape and reel table gives 1000 pieces for this string against 2500 for the narrow body, so the wide body arrives on a smaller reel.

Is the .A row a newer version? No. The .A row of this string is marked Obsolete, and the plain string is the one in production.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.