Contact Us

UCC28C44DR

Brand: Texas Instruments
Texas Instruments UCC28C44DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC28C44DR — Power Management & Signal Chain | Superb Automation

UCC28C44DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC28C44DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC28C44DR: a current mode PWM controller for off-line flyback and forward stages, with a 14.5 V start threshold, a 50 per cent duty ceiling and a 1 MHz oscillator, in an eight pin SOIC on a 2500 piece reel

UCC28C44DR is a fixed frequency peak current mode controller with a trimmed oscillator discharge, a 5 V reference, a 2.5 V error amplifier reference and a 1 A totem pole output stage, built as the pin compatible successor to the UC3844 family in a SOIC body of 8 pins. The D body is the eight pin SOIC that the UC384x family made a standard, and the part exists because an off-line converter still needs a controller that starts from a high voltage rail through one resistor and then runs from its own bias winding.

Order code and package

Catalogue stringUCC28C44DR, where D is the eight pin SOIC and R is the 2500 piece large reel
BodySOIC, D, eight pins, the same pinout as the UC3844 and the UCC38C44, which is what makes it a drop in for an existing board
Reel2500 pieces on a large tape and reel, the same count on the plain row and on the .A row
Alternate bodythe same die ships in VSSOP as UCC28C44DGKR, also 2500 pieces, for boards that want a smaller outline
Finish and moistureNIPDAU plating with the moisture column reading level 2 at 260 C and one year of floor life on the row that carries the reel count
Temperatureminus 40 to 125 C, which is the UCC28C4x grade; the UCC38C4x series in the same document stops at 85 C
Marking28C44 on the body, with a second line carrying the lot trace code
DocumentSLUS458I, July 2000, revised June 2024
StatusActive and in production on the addendum dated 15 July 2026

Electrical parameters that decide the application

Start threshold13.5 V minimum, 14.5 V typical and 15.5 V maximum, with the turn off point at 8 V minimum, 9 V typical and 10 V maximum, so a bias winding has to hold about 9 V after start
Duty ceiling47 per cent minimum and 48 per cent typical, because the output stage is driven through an internal toggle flip flop that halves the oscillator frequency
Oscillator50.5 to 55 kHz with a 10 kOhm timing resistor and a 3.3 nF capacitor, up to 1 MHz, with a trimmed discharge current of 7.7 to 9 mA
Reference5 V plus or minus 2 per cent at 1 mA, with a total window of 4.82 to 5.18 V, and a short circuit source current of 30 to 55 mA
Error amplifier2.475 to 2.525 V reference at 25 C, 90 dB of open loop gain and 1.5 MHz of unity gain bandwidth
Current sensea 3 V per V gain from the sense pin to the comparator, a 1 V maximum input signal and 35 to 70 ns from the sense pin to the output
Start-up current50 uA typical and 100 uA maximum, which is what sets the size of the resistor that feeds the part from the high voltage rail
Operating current2.3 mA typical and 3 mA maximum with no load on the output, so the bias winding only has to supply a few milliamps
Output stage1 A peak source and sink, 10 to 25 Ohm pull up and 5.5 to 15 Ohm pull down at 200 mA, with 25 ns rise and 20 ns fall into 1 nF
Undervoltage lockouthysteresis of about 5.5 V between the start and stop thresholds, which is deliberate, because a converter that restarts on a small dip will hiccup on every line sag
Duty floorzero, because the error amplifier can force the comparator to skip every cycle once the feedback voltage passes 2.6 V
Thermalspecified over minus 40 to 125 C junction on the UCC28C4x rows and 0 to 85 C on the UCC38C4x rows

Family variants and how they differ

UCC28C42 and UCC38C42the same 14.5 V start and 9 V stop window with a 100 per cent duty ceiling, for a flyback that needs the extra duty at low line
UCC28C43 and UCC38C43an 8.4 V start and 7.6 V stop window with a 100 per cent ceiling, the choice when the converter runs from a 12 V rail rather than from a rectified mains
UCC28C40 and UCC38C40a 7 V start and 6.6 V stop window, aimed at battery systems where the rail sags to 7 V
UCC28C41 and UCC38C41the 7 V window with the 50 per cent ceiling, the battery counterpart of the part on this page
UCC28C44 against UCC38C44identical electrically apart from the temperature grade, 125 C against 85 C, and the price difference is the reason both exist
UCC28C44 against UCC28C45the 45 has the 8.4 V window and the same 50 per cent ceiling, so the number to check on an existing bill of materials is the fourth character rather than the family

Points to check before this part goes on a BOM

The 50 per cent ceiling is the whole reason to choose this member of the family. A flyback run in continuous conduction with a duty above 50 per cent needs slope compensation that actually works, and a controller without it will oscillate at half the switching frequency as soon as the load passes the boundary. The UCC28C44 halves the output frequency with a toggle flip flop and caps the duty, which removes that failure mode at the cost of a higher primary current for the same power. A forward converter with a reset winding needs the same ceiling for a different reason, because the reset voltage has to be allowed for inside the off time.

The start and stop window of 14.5 V and 9 V is set for a converter fed from a rectified 85 V to 265 V mains, where the bias winding can easily produce 12 to 15 V. Using the part from a 12 V rail is a mistake that shows up as a converter that will not start, because 12 V sits below the 13.5 V minimum start threshold. The UCC28C45 in the same document has an 8.4 V window for exactly that case, and the two parts share a pinout, so the substitution is a bill of materials change rather than a board change.

Start-up current of 50 uA is the number that sizes the resistor from the high voltage rail, and it is easy to get wrong by a factor of three. At 375 V of rectified mains and 100 uA of worst case start-up current the resistor dissipates 37 mW, so a 0.25 W part is comfortable, but the same resistor also has to charge the input capacitor before the part starts, and that delay is what the customer notices as a slow power up. A 100 kOhm resistor with a 22 uF capacitor gives a time constant of 2.2 seconds, which is far too slow for most products and is the reason the value is usually nearer 50 kOhm with a smaller capacitor.

The current sense input is a comparator with a 1 V ceiling and a 3 V per V gain, and the propagation delay from the sense pin to the output is 35 to 70 ns. At 100 kHz that delay is under one per cent of a period and can be ignored. At 500 kHz it is three per cent of a period, and the peak current overshoot that comes with it has to be allowed for in the sense resistor. A board that moves from 65 kHz to 300 kHz to shrink the transformer without rechecking the sense resistor will run the primary switch above its current rating on every cycle and fail on a hot day.

The output stage is a totem pole rated at 1 A peak with 25 ns rise and 20 ns fall, which is enough for a 100 nC gate at 100 kHz and not enough for a paralleled pair of large FETs. The gate resistor sets the trade between switching loss and ringing, and the 10 to 25 Ohm pull up against the 5.5 to 15 Ohm pull down means turn off is the faster edge. That asymmetry is deliberate and worth keeping, because a slow turn off in a flyback puts the switching loss in the FET rather than in the snubber.

The reference is 5 V at 1 mA and the error amplifier reference is 2.5 V, and both are trimmed to about 2 per cent. The 5 V reference can supply 20 mA for a housekeeping load, but the same pin is the top of the feedback divider, so any current drawn from it appears as a regulation error. A board that powers an optocoupler's phototransistor from that pin, which is common in off-line supplies, will see the output voltage shift with the opto current, and the fix is a separate regulator or a buffer rather than a tighter resistor tolerance.

Reading a 14.5 V start window against a real bias winding

The bias winding has to deliver the start threshold before the converter runs and the stop threshold after it does, and the gap between 9 V and 14.5 V is wide enough that a badly coupled winding will start the converter and then let it drop out on the first heavy load step. The usual symptom is a supply that starts into no load and shuts down when the load arrives, and the cause is a bias capacitor that is too small rather than a controller fault. A 22 uF capacitor and a winding that holds 12 V at full load is the starting point, and the measurement to make is the bias rail on a scope during a load step rather than at steady state.

The other half of the window is the resistor from the high voltage rail. It has to supply the 100 uA maximum start-up current plus the leakage of the capacitor it charges, and it has to be able to do so at the lowest line voltage the product will see. At 85 V of mains the rectified rail is about 120 V, so a 100 kOhm resistor passes 1.2 mA, which is twelve times the start-up current and comfortably enough. At 100 kOhm and 375 V the same resistor dissipates 1.4 W, which is why the value is usually split into two resistors in series rather than one.

What a drop in replacement has to match

The pinout is the easy part: eight pins, same functions, same order as the UC3844. What has to be checked is the oscillator, because the timing components were chosen for a particular frequency and the discharge current of the newer part is trimmed, which shifts the frequency slightly for the same resistor and capacitor. A 5 per cent frequency shift is harmless in a flyback and can be the difference between passing and failing a conducted emissions limit, because the switching harmonic moves onto a different part of the measurement curve.

The second item is the current sense filter. The newer part has a faster comparator path, so a filter that was tuned to slow the old part down will now delay the trip point too much and let the peak current run higher than the resistor was sized for. The third item is the output drive, which is stronger, and a gate resistor that was chosen for the old part will now produce a faster edge and more ringing. A replacement that measures well at no load and fails at full load is usually one of these three rather than a defective part.

Where this order code fits

This is the controller in an off-line flyback for an industrial adapter, a charger, a lighting driver or an auxiliary supply inside a larger product, and in a forward converter that needs a hard duty ceiling for its reset scheme Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

Can it run from a 12 V rail? Not reliably. The start threshold is 13.5 V minimum, so a 12 V rail sits below it. The UCC28C45 in the same document has an 8.4 V window and the same pinout.

Why is the duty limited to 50 per cent? The output stage is driven through a toggle flip flop, so the output frequency is half the oscillator frequency and the maximum duty is 48 per cent typical. That removes the need for slope compensation in a continuous mode flyback.

What sets the switching frequency? The timing resistor and capacitor on the RT/CT pin. 10 kOhm and 3.3 nF give 53 kHz typical, and the oscillator is usable up to 1 MHz.

How much gate charge can it drive? 1 A peak source and sink, which covers a 100 nC gate at 100 kHz. Two large FETs in parallel need a buffer stage.

Is it a drop in for a UC3844? Pin for pin yes, and the electrical differences to check are the oscillator frequency for the same timing components, the current sense delay and the stronger output drive.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.