Contact Us

UCC2808AQDR-2Q1

Brand: Texas Instruments
Texas Instruments UCC2808AQDR-2Q1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC2808AQDR-2Q1 — Power Management & Signal Chain | Superb Automation

UCC2808AQDR-2Q1

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC2808AQDR-2Q1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC2808AQDR-2Q1: a current mode push-pull PWM controller with two alternating outputs, a 4.3 V start threshold and a 130 uA start-up current, in an eight pin SOIC on a 2500 piece reel

UCC2808AQDR-2Q1 is a low power current mode controller for push-pull, half bridge and forward converters, with two output stages that alternate at half the oscillator frequency and a discharge transistor on the current sense pin that resets the filter every cycle in a SOIC body of 8 pins. The D body is the eight pin SOIC that this family has used since the UCC3808, and the part exists because a push-pull converter fed from a 12 V or 24 V battery rail needs a controller that starts at 4.3 V and draws 130 uA while it waits.

Order code and package

Catalogue stringUCC2808AQDR-2Q1, where A is the revision with the current sense discharge transistor, 2 the 4.3 V start window, D the eight pin SOIC and Q1 the automotive grade suffix
Order code notethe vendor document SLUS456G does not print this string in its orderable table; the published rows are UCC2808ADTR-2 and its .A and G4 variants at 2500 pieces, so the Q1 suffix has to be confirmed against the automotive document or a customer purchase order before it is committed
BodySOIC, D, eight pins in a 4.9 mm by 6 mm outline, the same pinout as the UCC3808 family and the UC3846 half bridge family in its eight pin form
Reel2500 pieces on a large tape and reel for the published rows, NIPDAU plating and moisture level 1 at 260 C with no floor life limit
Temperatureminus 40 to 85 C on the UCC2808A rows, against 0 to 70 C on the UCC3808A rows in the same document
Marking2808A-2 on the published rows
DocumentSLUS456G, April 1999, revised July 2025, covering UCC2808A-1 and -2 and UCC3808A-1 and -2
Statusthe published industrial rows are active; the tube rows UCC2808AD-1 and UCC2808AD-2 are marked Obsolete

Electrical parameters that decide the application

Start threshold4.1 V minimum, 4.3 V typical and 4.5 V maximum on the -2 version, with a minimum operating voltage after start of 3.9 V, 4.1 V and 4.3 V and only 0.1 V to 0.3 V of hysteresis
Start-up current130 uA typical and 260 uA maximum below the start threshold, which is what sets the resistor from the battery rail and the time it takes to charge the bias capacitor
Run current1 mA typical and 2 mA maximum with the feedback at zero and no gate load, so the bias winding only has to supply a couple of milliamps
Oscillator194 kHz typical with a 22 kOhm resistor and a 330 pF capacitor, with a 175 kHz to 213 kHz window and operation up to 1 MHz
Output timingtwo outputs that alternate at half the oscillator frequency, each capped at 48 to 50 per cent duty, with 60 ns to 200 ns of dead time set by the timing components
Reference2.0 V on the error amplifier input, with a 1.95 V to 2.05 V window and 60 dB to 80 dB of open loop gain
Current sense2.2 V per V of gain, 0.5 V of maximum input signal, 100 ns to 200 ns from the sense pin to the output and a 0.75 V over current threshold
Sense dischargea transistor from the CS pin to ground that turns on during the oscillator dead time, with 5 mA to 10 mA of sink current, which removes the filter capacitor charge every cycle
Output stage500 mA peak source and 1 A peak sink, with 25 ns rise and 60 ns fall into 1 nF, enough for a small FET directly and not enough for a paralleled pair
Bias clampan internal zener that holds VDD at 13 V to 15 V when the bias is fed through a resistor, which allows a cheap dropper from a high rail instead of a regulated supply
Soft startthe COMP pin rises from 0.5 V to 4 V in 3.5 ms to 20 ms, which is the soft start and also the limit on how fast the converter can respond to a load step
Thermalan eight pin SOIC without an exposed pad, so the dissipation is small by construction: the part drives a gate and nothing else

Versions, suffixes and the automotive question

The -2 version, the part on this page4.3 V start window with 0.2 V of hysteresis, for a converter fed from a 5 V or 12 V battery rail that must not restart on a small dip
The -1 version12.5 V start threshold and 4.2 V of hysteresis, for an off-line converter fed from a rectified mains rail through a dropper resistor
UCC3808A in the same documentthe same function in a 0 to 70 C grade, which is the cheaper part for a consumer product and the wrong part for an industrial one
Against a push-pull controller with a fixed 50 per cent limit and no discharge transistorthe discharge transistor removes the filter capacitor charge every cycle, which shortens the current sense delay and allows a smaller filter
Against a half bridge controllerthe same two alternating outputs at half the oscillator frequency, with the difference in how the switches are driven rather than in the control loop
The automotive questionthe Q1 suffix in the catalogue string is not in this document, so the automotive grade has to be sourced against its own document rather than inferred from the suffix

Points to check before this part goes on a BOM

The 0.2 V of hysteresis on the -2 version is the number to read first. A 4.3 V start threshold with 0.2 V of hysteresis means the converter stops at 4.1 V and starts again at 4.3 V, and a battery rail that sags under a motor start will cross that band repeatedly. The result is a converter that hiccups instead of dropping out cleanly, and the current that a hiccuping push-pull draws from a sagging battery makes the sag worse. The -1 version has 4.2 V of hysteresis for exactly this reason, and choosing between them is a question about the source impedance rather than about the converter.

The current sense discharge transistor is the quiet improvement in the A revision. A peak current mode controller compares the sense voltage against the error amplifier output, and any filter capacitor on the sense pin holds charge from the previous cycle, so the comparison starts from the wrong point. The A revision turns a transistor on during the oscillator dead time and dumps that charge, with 5 mA to 10 mA of sink current, so every cycle starts from zero. The practical gain is a smaller filter capacitor and a shorter current sense delay, which shows up as a converter that holds its limit more accurately at high line.

A duty ceiling of 48 to 50 per cent per output is a property of the topology rather than a limitation of the controller. In a push-pull both halves of the transformer primary are driven alternately, and a duty above 50 per cent on either half would mean both halves conducting at once, which shorts the transformer. The dead time of 60 ns to 200 ns between the two outputs is the time when neither half conducts, and it is set by the timing components rather than by a separate pin, so changing the oscillator frequency also changes the dead time.

The switch from the UCC3808 to the UCC2808A is a temperature range change and a silicon revision in one step, and a bill of materials that carries the old string needs both checked. The published rows in this document show UCC2808AD-1 and UCC2808AD-2 as Obsolete in the tube packing, while the reeled strings are active, so a low volume build that ordered tubes is now buying from a cut reel or moving to the reel part number. That is a purchasing change rather than an electrical one, and it is the sort of change that is discovered two weeks before a build.

The automotive suffix is the one thing on this page that cannot be settled from the document. The catalogue entry is UCC2808AQDR-2Q1 and the vendor document prints UCC2808ADTR-2, its .A row and a G4 row, with a minus 40 to 85 C range and no automotive qualification statement. An automotive grade of this function exists as a separate document with its own orderable table, so the string has to be checked against that table before a production order is placed, and a quote should carry the grade the vendor actually publishes rather than the grade the suffix implies.

What a push-pull controller has to get right

The two output stages have to be matched in delay, because a mismatch turns into a DC offset in the transformer flux. The controller's own matching is good, but the gate drive path is where the mismatch appears, so a push-pull built with one long gate trace and one short one will walk the flux in one direction and saturate the core on a hot day. That is why the two gate loops are routed as a pair and why the current sense is taken on the primary rather than on one half.

The current sense discharge also matters for flux balance. A cycle that starts its comparison from a stale capacitor voltage trips late, delivers more volt seconds on that half, and pushes the flux further. The discharge transistor removes that source of asymmetry, and the filter capacitor that remains can be small enough that its time constant is a fraction of the switching period rather than several periods.

Starting from a battery rail with 130 uA

The start-up current of 130 uA is what allows a dropper resistor from a 24 V rail to charge the bias capacitor while the controller waits. A 100 kOhm resistor passes 240 uA at 24 V, so the capacitor sees about 110 uA of net charging current and a 10 uF capacitor takes about a second to reach 4.3 V. That second is the delay the product shows between the switch being turned on and the output appearing, and it is also the reason the bias capacitor has to be a low leakage type: a capacitor that leaks 50 uA never reaches the threshold at all.

After start the bias has to come from somewhere better than the dropper, because 240 uA is not enough to run the part at 2 mA plus gate charge. A bias winding on the transformer is the normal answer, and the winding has to deliver 5 V or more at the lowest input voltage with the converter at full load. A winding that delivers 5 V at nominal input and 3.8 V at low line drops the part below its 4.1 V stop threshold, and the converter restarts into the same condition, which is the classic hiccup at low line.

Where this order code fits

This is the controller in a push-pull or half bridge converter fed from a 12 V or 24 V battery rail, in a telecom point of load module, a battery charger, an inverter or a low power isolated supply Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.

Questions buyers ask

Why is the hysteresis so small on the -2 version? Because it is built for a battery rail that must not restart on every dip. The trade is that a soft rail with heavy sag will make the converter hiccup rather than drop out cleanly.

Can it drive the FETs directly? 500 mA of source and 1 A of sink peak is enough for a small FET with a gate charge under about 30 nC. A larger FET needs a buffer or a driver stage.

What sets the dead time between the two outputs? The timing resistor and capacitor on the oscillator pin. The vendor quotes 60 ns to 200 ns depending on those values, so changing the frequency also changes the dead time.

Is the Q1 part in this document? No. The document prints the industrial rows only, so the automotive grade has to be confirmed against its own table before a purchase order.

What does the discharge transistor do? It empties the current sense filter capacitor during the oscillator dead time, so each cycle starts its comparison from zero. That shortens the sense delay and makes the current limit hold more accurately.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.