UCC28070QPWRQ1
Product Specifications
UCC28070QPWRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC28070QPWRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC28070QPWRQ1: interleaved continuous conduction mode power factor controller
UCC28070QPWRQ1 is a two phase interleaved power factor correction controller in a TSSOP body of 20 pins. The two pulse width modulators run 180 degrees apart, which halves the ripple the input filter has to absorb. Current synthesis means one shunt per phase and no second current transformer, and the quantised voltage feed forward keeps the power factor near unity across the line range. This order code carries the automotive qualifier.
Order code and package
| UCC28070QPWRQ1 | the automotive string on this page; the document covers UCC28070 and UCC28070A and its addendum prints no Q1 row, so reel size and marking have to come from the automotive document or a vendor confirmation |
| UCC28070APWR | TSSOP-20, 2000 pieces on a large reel, active, the extended frequency member |
| UCC28070DWR | wide body SOIC-16, 2000 pieces on a large reel, active |
| UCC28070PWR | TSSOP-20, 2000 pieces on a large reel, active, 30 kHz floor |
Electrical parameters that decide the application
| Supply lockout | turn on at 9.8 V minimum, 10.2 V typical, 10.6 V maximum, with hysteresis on the falling edge |
| Reference | 5.82 V minimum, 6.00 V typical, 6.18 V maximum at no load, enable threshold 7.5 to 8.5 V on the rising supply |
| Switching frequency | 95 to 105 kHz with a 24.9 kOhm timing resistor and a 22.6 kOhm duty resistor, 9.75 to 10.75 kHz at the low end with 750 kOhm and 681 kOhm |
| Duty cycle clamp | 92 to 98 per cent with the same resistor pair, set by the ratio rather than by a register |
| Phase relationship | 179 to 181 degrees between the two gate outputs |
| Quantised feed forward | eight levels on the VINAC pin at 0.7, 1.0, 1.2, 1.4, 1.65, 1.95, 2.25 and 2.6 V |
| Multiplier gain | 17 uA typical with the amplifier output above 1.5 V |
| Current sense pins | CSA, CSB and PKLMT are limited to 3.3 V, and the peak limit threshold is set by a divider from the 6 V reference |
Family variants and how they differ
| UCC28070A | 10 kHz to 300 kHz, the wider floor, and the only electrical difference from the plain device |
| UCC28070 | 30 kHz to 300 kHz, the original member |
| PW body | TSSOP-20, 2000 piece reel or 70 and 25 piece tubes |
| DW body | wide SOIC-16, 2000 piece reel, the same die in a wider body |
| Automotive | the Q1 string is listed as another qualified version of the family and is not printed in this addendum |
Points to check before this part goes on a BOM
Interleaving is the whole point of the part. Two phases 180 degrees apart cancel the ripple current at the summing node, so the input capacitor and the EMI filter can be smaller and the conducted emission at twice the switching frequency largely disappears instead of having to be filtered.
Current synthesis removes the second current transformer. The device reconstructs the inductor current from the switch current and the duty cycle, which is why the document describes a down slope programming resistor and why the current sense pins only ever see a fraction of the phase current.
The duty clamp is a resistor ratio, not a number in a register. The 92 to 98 per cent window in the electrical table belongs to a 24.9 kOhm timing resistor and a 22.6 kOhm duty resistor, and the value moves with both, so a copied divider can leave a board clamping earlier than intended.
The eight feed forward levels are quantised on the VINAC pin. Each level steps the multiplier gain, so the input current follows the line voltage in steps rather than continuously, and the power factor depends on that staircase being matched to the line range of the product.
The automotive string on this page is not printed in the addendum of this document. The addendum lists UCC28070APW, APWR, DW, DWR, PW and PWR rows only and points to UCC28070-Q1 as another qualified version, so reel size, marking and grade for the Q1 string have to be confirmed on the automotive document before a purchase order is placed.
The 6 V reference is the anchor for three separate divider networks: the peak current limit, the amplifier output range and the quantised feed forward ladder. A reference that reads 5.82 V at one end of the window moves all three, which is why the current limit is specified as a threshold on the sense pin rather than as a current in amperes.
The 180 degree phase relationship is measured between the two gate outputs and specified as 179 to 181 degrees, so the interleaving is trimmed rather than nominal. On a board where the two phases feed a common input capacitor, a one degree error is already a small asymmetry in the ripple cancellation, and that asymmetry is what the capacitor ripple current rating has to absorb.
Why the frequency floor differs between the two members
The A member reaches down to 10 kHz and the plain member stops at 30 kHz. On a high power unit the lower floor lets switching loss fall far enough to keep a large IGBT bridge cool, at the cost of a bigger inductor on each phase, and on a smaller unit the 30 kHz floor is never approached. The rest of the electrical table is shared, so the two cross reference on everything except the timing resistor range.
The 3.3 V limit on the current sense pins is the number that catches a first board. A shunt on a 3 kW unit at 0.5 V of full scale swing has enough headroom, but a divider copied from a controller with a 5 V input range will clamp the current amplifier long before the peak limit is reached.
How the two phases share current without a second transformer
Current synthesis works from the switch current in each phase plus the duty cycle, and the reconstruction is what turns a single shunt per phase into a full inductor current waveform. The accuracy of that reconstruction depends on the down slope resistor and on the inductor value, so a build that changes the inductor without changing that resistor loses the current matching between phases and the input ripple grows back.
The peak limit is a comparator on the reconstructed current, not on the switch current, so it trips on the inductor peak rather than on the switch peak. That is the figure a magnetics engineer needs, and it is also why the threshold is programmed as a voltage on the sense pin rather than as a fixed ampere value inside the part.
Where this order code fits
Air conditioners and major appliances, telecom and server power, televisions and professional audio are the applications named in the document, and each of them runs a continuous conduction mode boost stage ahead of a resonant converter. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Is the Q1 string the same die as the industrial part? The document lists the automotive string as another qualified version of the family rather than as a row in the addendum, so the qualification is separate even when the silicon is shared.
What sets the maximum duty cycle? A resistor from the DMAX pin to ground sets it as a ratio against the timing resistor, and the 92 to 98 per cent window applies to the 24.9 kOhm and 22.6 kOhm pair used in the electrical table.
How many current shunts does the circuit need? One per phase. The synthesis reconstructs the inductor current, so no second current transformer is required, which is the cost argument for the part.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.