UCC2806DWTR
Product Specifications
UCC2806DWTR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC2806DWTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC2806DWTR: a dual output current mode PWM controller with alternating gate drives, a 3x differential current sense amplifier and 125 ns of circuit delay, in the sixteen pin wide SOIC, now marked not recommended for new builds
UCC2806DWTR is a current mode controller that drives two external FETs alternately from a single oscillator, with the dead time set by the timing capacitor and a differential current sense amplifier that reads the primary current across a shunt instead of a single ended pin in a SOIC body of 16 pins. The DW body is the wide sixteen pin SOIC, and the family also exists in the narrow D body, the TSSOP and the ceramic packages, which is why the same die carries several different reel sizes in the addendum.
Order code and package
| Catalogue string | UCC2806DWTR, where 2806 is the industrial temperature member of the dual output family, DW is the wide sixteen pin SOIC and TR is tape and reel |
| Body | SOIC, DW outline, sixteen pins, the wide body with 27 C per watt junction to case and 50 to 100 C per watt junction to ambient depending on the copper area |
| Reel | the addendum prints 2500 pieces on a large reel in the row area and 2000 in the carrier table for the same string, so the reel size has to be named on the order |
| Status | the DW rows read not recommended for new builds on the current addendum while the UCC2806D rows in the narrow body still read Active, which is the single most important fact on this page |
| Finish and moisture | NIPDAU at moisture level 2 for 260 C with a one year floor life |
| Temperature | minus 40 to 85 C for the 2806 member, against minus 55 to 125 C for the 1806 and zero to 70 C for the 3806 |
| Architecture | the same block diagram and pinout as the UC3846 family, in a BiCMOS process that cuts the bias currents by an order of magnitude |
| Document | SLUS272F, February 2000, revised August 2006, a document that has not been revised since 2006 and should be read with that in mind |
Electrical parameters that decide the application
| Start threshold | 6.5 V minimum, 7.5 V typical and 8.0 V maximum on VIN, with 0.75 V of hysteresis, so a five volt rail needs a boost stage before the controller will start |
| Startup current | 50 microamps typical below the start threshold, which is what allows a resistor from the input rail to charge the bias capacitor without dissipating continuously |
| Operating current | 1.0 mA typical and 1.4 mA maximum, a fraction of the bipolar part it replaces and the reason the start resistor can be large |
| Output current | plus or minus 0.5 A peak per output, with the two outputs alternating, so the total gate charge delivered per cycle is split across the two pins |
| Duty cycle | zero to 50 per cent per output, with the minimum dead time set by the timing capacitor value rather than by a fixed internal interval |
| Current sense amplifier | a 3x differential amplifier with CS+ and CS- inputs, which rejects the common mode ground noise that a single ended sense pin cannot |
| Circuit delay | 125 ns from the current sense input to the output, which sets the minimum on time and therefore the peak current overshoot at the top of a short circuit |
| Shutdown | 1.0 V threshold with 75 to 150 ns of delay to the output, forcing both gate drives low from a single pin |
| Oscillator | the timing capacitor is discharged to ground through a 2.5 mA sink, and the discharge interval is the dead time, so the capacitor value sets frequency and dead time at once |
| Reference | 5.1 V nominal, and it supplies the error amplifier divider as well as the oscillator timing resistor |
| Synchronisation | a SYNC pin with TTL compatible thresholds, so several controllers can be locked to one clock in a parallel arrangement |
| Current limit | the CURLIM pin programs whether an over current latches off or retries, which is a board level choice rather than a part number choice |
| Thermal | 27 C per watt junction to case in the wide body, against 35 in the narrow body, so the wide outline is the one to use when both outputs drive large gates |
Family variants and how they differ
| UCC1806 | minus 55 to 125 C, same die, same pinout, the military temperature member |
| UCC3806 | zero to 70 C, the commercial member, still listed Active in several bodies |
| Narrow body | the D outline carries the same pinout in a smaller body, with the same 0.5 A outputs and the same 125 ns delay |
| TSSOP and SSOP | the PW and DBQ bodies carry 2000 and 75 piece packing respectively, and the SSOP rows in the addendum are shifted by one line so the body has to be read against the drawing |
| Ceramic | the J and L packages are the through hole and ceramic versions for programmes that cannot use plastic, and they are marked NRND as well |
| Function | this is a current mode controller with alternating outputs, not a push pull driver, so it does not include the isolation or the dead time trimming that a dedicated push pull controller would |
Points to check before this part goes on a BOM
The status is the first thing to check. The wide body rows on the current addendum read not recommended for new builds, while the narrow body UCC2806D rows still read Active. A new build should either use the narrow body or move to a current controller, and a repair or a legacy build should plan a last time buy rather than assume availability.
The 3x differential current sense amplifier is the reason this part is still found in legacy boards. It reads the primary current across a shunt with both ends brought out, so the ground bounce of a high current loop does not appear as a current signal, which is exactly the problem that a single ended CS pin has on a 500 W converter.
The dead time is not a fixed internal interval. The timing capacitor is discharged through a 2.5 mA sink and the discharge time is the dead time, so changing CT to change frequency also changes the dead time, and a substitution that keeps the frequency and changes the capacitor value can cross conduct the two FETs.
The 125 ns circuit delay is short for a part of this age and it is what makes the current limit usable at high frequency. At 100 kHz the delay is 1.25 per cent of the period, so the peak current overshoot during a short circuit is a fraction of an amp rather than several amps.
Bias current of 1.4 mA maximum against the bipolar UC3846 is the whole point of the BiCMOS version, and it is what lets a start resistor from a 400 V rail be large enough to stay cool. On a repair, a controller that will not start is more often a dried bias capacitor than a failed part.
The document has not been revised since 2006, so its addendum reflects the packing that existed then. Reel sizes and the status of the .A rows should be confirmed against a current vendor listing before a purchase order, particularly on a part that is already flagged.
Where this part still fits
Dual output current mode controllers survive in push pull, half bridge and forward converters where two gates have to be driven with a guaranteed dead time and a current limit that acts within one cycle. The alternating outputs and the differential sense amplifier are the two features that kept this family in production long after the single ended parts moved to newer processes.
For a legacy board the practical questions are the body, because the narrow and wide outlines carry different status, and the CURLIM setting, because a latch off after an over current event turns a transient fault into a supply that stays down until the input is cycled.
Where this order code fits
Push pull and half bridge converters, telecom and industrial DC to DC stages, battery chargers, and legacy boards where a dual alternating gate drive with a differential current sense amplifier is already qualified Teams comparing it with a neighbouring part start from our Obsolete Part Cross Reference Hub page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.
Questions buyers ask
Is this part still available for new builds? The wide body rows on the current addendum read not recommended for new builds, while the narrow D body rows read Active. A new build should confirm the body and the status before the BOM is frozen.
What is the advantage of the differential current sense? Both ends of the shunt are brought into a 3x amplifier, so the voltage developed by ground return currents does not appear as current. On a single ended sense pin that same voltage is read as current and limits the converter early.
How is the dead time set? By the timing capacitor. The capacitor is discharged through a 2.5 mA sink and the discharge interval is the dead time, so frequency and dead time move together and cannot be set independently.
Can two of these be synchronised? Yes. The SYNC pin takes a TTL level clock, so several controllers can run from one oscillator in a parallel or multiphase arrangement.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Last-Time-Buy and LTB Planning page sets out the checks that keep a substitute from failing on the bench.