Contact Us

UCC27524DR

Brand: Texas Instruments
Texas Instruments UCC27524DR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC27524DR — Power Management & Signal Chain | Superb Automation

UCC27524DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC27524DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC27524DR: dual 5 A gate driver with 1 ns delay matching between channels

UCC27524DR is two independent 5 A low side gate drivers in one 8 pin package, with a 17 ns typical delay, 1 ns of matching between the channels and enable pins that can be tied together for a single control line in a SOIC body of 8 pins. The UCC27524 carries two identical driver channels, each capable of 5 A peak source and sink current, from a single supply of 4.5 V to 18 V. Propagation delay is 17 ns typical, rise and fall times are 6 ns and 10 ns, and the two channels match within 1 ns. Inputs and enables accept negative excursions to -5 V and are not restricted by the supply rail, and the outputs are held low while VDD is below its UVLO threshold. The body is the 8 pin SOIC, and the DC current rating per output is 0.3 A.

Order code and package

Order codeUCC27524DR
Supply voltage, VDD4.5 V to 18 V
Peak source and sink current5 A per channel, pulsed
Continuous output current0.3 A per channel
Propagation delay17 ns typical
Rise and fall time6 ns and 10 ns typical
Delay matching between channels1 ns typical
Input voltage range-5 V to 20 V on the D and DGN bodies
Package8 pin SOIC, D body
Pin count8
DocumentSLUS845, dual 5 A driver family, revision current at download

Electrical parameters that decide the application

VDD absolute maximum20 V
Output pulsed current5 A
Output continuous current0.3 A
VDD UVLO rising3.8 V minimum, 4.1 V typical, 4.4 V maximum
VDD UVLO falling3.5 V minimum, 3.8 V typical, 4.1 V maximum
UVLO hysteresis0.3 V
Quiescent current per channel at 3.4 V300 uA typical, 450 uA maximum
Static supply current0.6 mA typical, 1.0 mA maximum
Operating current at 1 MHz3.2 mA typical, 3.8 mA maximum
Disable current0.8 mA typical, 1.1 mA maximum
Output pullup resistance2.5 ohm typical, 5 ohm typical, 7.5 ohm maximum
Output pulldown resistance0.15 ohm typical, 0.5 ohm typical, 1 ohm maximum
Enable high threshold1.8 V to 2.3 V
Enable low threshold0.8 V to 1.2 V
Thermal resistance, D body126.4 C per W junction to ambient
Thermal resistance, DGN body48.9 C per W junction to ambient
Junction range-40 C to 150 C

Points to check before this part goes on a BOM

The continuous rating and the pulsed rating are two different parts of the same datasheet. An output can carry 5 A for a pulse and 0.3 A continuously, so the part is not a linear amplifier and cannot hold a DC gate bias of any consequence. The pulsed number describes the charge and discharge of a gate capacitor; the continuous number describes what the bond wires survive.

The output pullup resistance of 2.5 ohm typical and 5 ohm typical in the same table shows how the source path changes with the operating point, and the 7.5 ohm maximum is the number that sizes a turn on. Into a gate with 100 nC of charge, the source current starts near 5 A and falls as the gate rises, so the average is far below the peak. The pulldown side is much stronger, 0.15 ohm to 1 ohm, which is deliberate: turn off is the transition that has to be fast.

The 1 ns matching claim is a typical figure and it is measured between channels in the same package at the same load. It is not a guarantee over temperature, and the two channels can differ by the tolerance of their internal delay chains. A board that depends on matching to protect against shoot through should still set dead time from the maximum delay spread rather than from the typical.

Negative input capability of -5 V is specified on the D and DGN bodies only, and the DSD body is limited to -0.3 V. That difference matters in a motor drive, where the source of the low side device can swing below ground on a fast commutation and take the driver input with it. Choosing the body therefore changes the fault tolerance and not only the footprint.

Two thermal numbers are published for the same die: 126.4 C per W in the SOIC and 48.9 C per W in the HVSSOP with the PowerPAD. Driving 100 nC at 12 V and 200 kHz per channel is 0.24 W of gate charge loss across the two channels, which is a 30 C rise in the SOIC and 12 C in the pad version. Above roughly 300 kHz the SOIC body stops being the cheaper choice because it starts to set the case temperature.

The enable pins are independent and have their own thresholds, 1.8 V to 2.3 V for a high and 0.8 V to 1.2 V for a low, with a 200 kohm pullup when the pin is left open. That pullup means an unconnected enable is on, which is convenient in a prototype and dangerous in a product if the pin is left floating through a connector. Both enables can be tied to one control line when the two channels always run together.

The 3.2 mA operating current at 1 MHz is the current the part draws internally while switching, separate from the gate charge it delivers. At 12 V that is 38 mW in a package whose junction is within 126 C per W of ambient, which adds a few degrees and has to be counted in a high ambient enclosure. In a 60 C ambient the SOIC body at 0.3 W total sits about 98 C junction, which is inside the 150 C limit but leaves little room for a worse case.

Where this order code fits

This order code drives two switches that have to move together, such as the two phases of a synchronous buck, the two lower devices of a full bridge, or a pair of MOSFETs paralleled for a high current path. The 1 ns matching is what keeps a paralleled pair from sharing current unevenly during the switching transition, and the negative input capability is what keeps a ground bounce from latching the driver. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can both channels be paralleled? Yes, the datasheet states that the two outputs can be paralleled for higher drive current. The 1 ns matching is why the two share without an external balancing resistor.

Is the enable pin pulled up internally? Yes, 200 kohm to VDD, so an open enable is enabled. Fit a pull down if the pin can be left floating in the product.

What supply range does it need? 4.5 V to 18 V, with UVLO release between 3.8 V and 4.4 V at 25 C, so a 5 V rail works and a 3.3 V rail does not.

SUPERB supplies the SOIC tape and reel with date codes, packing and country of origin on the offer, and the BOM Shortage Recovery page lists what to compare before a driver position moves to another body.