Contact Us

UCC27517DBVR

Brand: Texas Instruments
Texas Instruments UCC27517DBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC27517DBVR — Power Management & Signal Chain | Superb Automation

UCC27517DBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC27517DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC27517DBVR: single channel 4 A low side gate driver in SOT-23

UCC27517DBVR is a low side gate driver that replaces a discrete NPN and PNP pair with one part and one resistor in a SOT-23 (DBV) body of 5 pins. It sources and sinks 4 A peak from a single supply between 4.5 V and 18 V, with a 13 ns propagation delay and 9 ns and 7 ns rise and fall times. The two input pins give a choice of inverting or non-inverting polarity, and the unused pin works as an enable.

Order code and package

Order code read outUCC27517 DBV R: device UCC27517, DBV five pin SOT-23, R large tape and reel
PackageSOT-23 (DBV), 5 pins, 2.90 mm by 1.60 mm
Carrier in the vendor addendumUCC27517DBVR at 3000 pieces on a large reel, with 250 piece small reel rows under the DBVT code
Moisture levelLevel 1, 260 degrees unlimited floor life
Lead finishNickel palladium gold, with a tin option on some rows
Part marking7517
Operating temperatureminus 40 to plus 140 degrees, junction and ambient

Electrical parameters that decide the application

Supply range4.5 V to 18 V, single supply, with the output held low during undervoltage lockout
Peak drive current4 A source and 4 A sink symmetrical, measured into 0.22 uF at 1 kHz
Continuous output current0.3 A DC, so the part drives a gate, not a load
Propagation delay13 ns typical, which is the number that sets the dead time budget
Rise and fall time9 ns and 7 ns typical, fast enough to keep a MOSFET out of its linear region
Undervoltage lockout4.20 V typical start, 3.90 V minimum operating after start, 0.3 V of hysteresis
Input thresholds2.2 V high and 1.2 V low, fixed and independent of the supply, with 1.0 V of hysteresis
Start up current60 to 100 uA depending on input state, which is what a controller sees before it enables the driver
Output high drop50 mV at 12 V and 10 mA, 60 mV at 4.5 V, so the gate reaches the rail
Output low drop5 mV at 12 V and 10 mA, which keeps the gate from floating up during the off time
Absolute maximum20 V on the supply, 4 A pulsed output for 0.5 ms, 150 degrees junction
Logic familyTTL and CMOS compatible, so a 3.3 V controller drives it without a level shift

Family members and how they differ

UCC27517single channel, 4 A source and sink, dual polarity input, the part on this page
UCC27516the same die in a six pin package, adding a separate enable pin
UCC27511asymmetric drive at 4 A source and 8 A sink for a turn off that has to be faster than turn on
UCC27518 and UCC27519same 4 A symmetrical drive in a five pin body, with different input logic
Package choicethe five pin SOT-23 and the six pin WSON share the drive core, so the selection is about board space and pin count

Points to check before this part goes on a BOM

A 4 A peak rating into a 0.22 uF load is a transient number. Continuous output current is limited to 0.3 A, which is the figure that matters when the driver has to hold a gate on for a long duty cycle at high frequency. At 500 kHz and 100 nC of gate charge the average current is 50 mA, comfortably inside the limit, but at 1 MHz with a large die the same arithmetic moves toward the 0.3 A boundary and the package temperature becomes the limit.

The input thresholds are fixed rather than ratiometric, which is the quiet advantage of this family. A 3.3 V logic signal crosses the 2.2 V high threshold regardless of whether the driver runs from 5 V or 15 V, so a controller and a driver on different rails do not need a level translator. The 1.0 V of hysteresis also means a slow rising enable signal produces one clean edge rather than a burst of oscillation.

Undervoltage lockout holds the output low, and that is a protection rather than a convenience. If the driver is powered from a bootstrap or a rail that comes up after the main supply, a floating gate during power up would turn the MOSFET partially on and dump the bus into it. Holding the output low through the lockout window is what makes the part safe in a hot plug or sequencing scenario.

The two input pins are not a convenience feature for polarity alone. With both pins available, the unused one works as an enable: tie the inverting input high and the non-inverting input becomes an active high enable, or tie the non-inverting input low and the inverting input becomes an active low shutdown. That gives a hardware interlock without an extra gate, which is often what a fault comparator needs.

Drive strength is only useful if the gate loop is short. At 9 ns rise time the di/dt through the gate is high enough that a 10 nH loop produces several volts of source bounce, which shows up as ringing on the gate and, in the worst case, a spurious turn on of the opposite FET in a bridge. The 5 mV low output drop helps here, because a low impedance sink holds the gate down while the switch node moves.

Where this order code fits

Used in switched mode supplies, DC to DC converters, motor drives, solar inverters, UPS units and as a companion driver for digital power controllers, including gate drive for wide band gap devices where a fast, stiff drive with tight timing is required. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can it drive a GaN device? The vendor lists wide band gap gate drive among the applications, and the 4.5 V to 18 V supply with a fixed input threshold suits a 5 V gate. A GaN part with a very low absolute gate rating needs the supply clamped and checked against its own data sheet.

What is the difference between the 16 and the 17? Pin count and enable. The UCC27516 puts the same driver core in six pins and adds a dedicated enable, while the UCC27517 uses the second input pin as the enable instead.

Is a gate resistor still needed? Usually a small one, to damp the gate loop and control the turn on di/dt. With 4 A of drive the resistor value is often between 1 and 10 ohm, and it should be chosen from the switching loss measurement rather than copied.

How much current does it draw while switching? Quiescent current is in the tens of microamps, and the operating current is dominated by the gate charge. At 300 kHz with 60 nC of gate charge the driver delivers about 18 mA plus the quiescent figure.

Is the part available in a small reel? Yes, the DBVT code is a 250 piece small reel and the DBVR code is a 3000 piece large reel. Both are on the published addendum, so a prototype can be bought without breaking a full reel.

What happens if both inputs are left floating? The thresholds have hysteresis but the pins have no defined default when floating, so a floating input can sit in the middle and produce a burst of switching. Tie the unused input to the supply or to ground, and use it as the enable rather than leaving it open.

How close should the driver sit to the switch? As close as the board allows, with the gate loop kept under about 10 nH. At 7 ns fall time a long loop produces source bounce of several volts, which shows up as ringing on the gate and as extra loss in the switch.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.