UCC27332QDGNRQ1
Product Specifications
UCC27332QDGNRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC27332QDGNRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC27332QDGNRQ1: 9 A of drive in a 3 mm by 3 mm body, with 5 V of input headroom
The UCC27332QDGNRQ1 is an automotive qualified single channel low side gate driver with 9 A typical sink and source current, a 4.5 V to 18 V operating range, a 20 V absolute maximum and a 25 ns typical propagation delay. The body is an 8 pin HVSSOP measuring 3.0 mm by 3.0 mm. It is built for the case where a controller output has to drive a large MOSFET or a parallel pair directly, and the 9 A peak is what turns a 100 nanocoulomb gate charge in about 12 ns instead of 60.
The input withstands minus 5 V, which is the detail that matters in a motor drive or an automotive power stage where the ground reference moves. An independent enable pin lets the power stage be shut down without waiting for the controller, so a fault comparator can pull the driver low in a few tens of nanoseconds. The thresholds are TTL compatible, the device is AEC-Q100 grade 1 qualified over minus 40 C to plus 125 C ambient, and the ESD classifications are HBM level H2 and CDM level C4B.
Key electrical data for the UCC27332QDGNRQ1
| Drive | 9 A typical sink and 9 A typical source, single channel low side |
| Supplies | 4.5 V to 18 V operating, 20 V absolute maximum, TTL compatible thresholds |
| Timing | 25 ns typical propagation delay, fast rise and fall into a large gate charge |
| Input | Withstands minus 5 V on the input pin, independent enable signal |
| Grade | AEC-Q100 grade 1, -40 C to +125 C ambient, HBM H2, CDM C4B |
| Body | DGN, 8 pin HVSSOP, 3.0 mm by 3.0 mm, industry standard pinout |
Package, marking and reel data
| Body | DGN, 8 pin HVSSOP with exposed pad, 3.0 mm by 3.0 mm |
| Reel | 2500 pieces on a large reel |
| Finish | NIPDAU, level 1 at 260 C with unlimited floor life |
| Marking | 332Q on the top, automotive grade with the Q1 suffix in the order code |
Driving a parallel MOSFET pair
Two MOSFETs in parallel double the gate charge, and a driver with 4 A peak takes twice as long to charge them, which pushes the switching loss up and the current sharing between the two devices apart. At 9 A the same pair switches in the same time as one device did on the smaller driver, so the paralleled pair keeps the thermal benefit without paying for it in switching loss. That is the reason this part sits in automotive pump and fan controllers, where two or three devices in parallel are normal.
The gate resistor still has to be chosen for the loop, not for the driver. A 2 ohm resistor with 9 A of drive gives an 18 V drop across the resistor, so the effective gate voltage during the Miller plateau is set by the resistor and the plateau current rather than by the supply. A build that copies a 10 ohm resistor from a 4 A driver will switch slowly and dissipate the difference in the MOSFET, while a 0.5 ohm resistor with 9 A of drive rings the gate and can exceed the gate oxide rating on a short loop, which is why the vendor quotes the rise and fall times into a defined 1000 picofarad load rather than into an unloaded gate. The resistor value has to be found with the actual loop inductance, not copied. Our power management cross reference page lists the single channel drivers we hold in this current class.
Buyer questions on the UCC27332QDGNRQ1
Can this drive a silicon carbide MOSFET? It can drive the gate, but it has no isolated barrier and no negative bias, so a high side SiC device needs an isolated driver and this part suits the low side or a grounded source arrangement.
What does the independent enable do? It shuts the output down without going through the controller, so a comparator can remove gate drive within the propagation delay rather than within a software cycle.
Is the 20 V absolute maximum enough for a 24 V system? The operating range stops at 18 V, so a 24 V rail needs a regulator or a different part. The 20 V absolute maximum is a transient limit, not an operating point.
Availability and cross reference
This code ships 2500 pieces per reel at level 1 with unlimited floor life, which keeps handling simple. Because the part is automotive grade, the lot has to be traceable and the AEC-Q100 record travels with the shipment. We quote the Q1 suffix explicitly, since the industrial code with the same body and a different qualification is not interchangeable on an automotive build. Our supplier quality audit page describes the record set we keep for grade 1 parts.