Contact Us

UCC27311ADRCR

Brand: Texas Instruments
Texas Instruments UCC27311ADRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC27311ADRCR — Power Management & Signal Chain | Superb Automation

UCC27311ADRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC27311ADRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC27311ADRCR: 3.7 A sink and 4.5 A source on a 120 V bridge, with 8 V of UVLO margin

The UCC27311ADRCR is a 120 V half bridge driver with asymmetric drive, 3.7 A sink and 4.5 A source, which is the combination a MOSFET gate wants: more source current to charge the gate quickly and a slightly smaller sink current to keep the turn-off edge from exciting the switch node. It runs from 8 V to 17 V with a 20 V absolute maximum, quotes 20 ns typical propagation delay, 7.2 ns rise and 5.5 ns fall into a 1000 picofarad load, and matches the two channels within 4 ns.

The switch node tolerance is the reason this part exists in industrial and telecom supplies. It survives a negative transient of 28 V minus VDD for less than 100 ns on the HS pin, which is a much larger excursion than the earlier family allows, and the input pins take minus 10 V to plus 20 V independent of the supply. On a 100 V bus with a fast MOSFET and a laminated bus bar that still has some inductance, that headroom is what keeps the driver alive through a short circuit test.

Key electrical data for the UCC27311ADRCR

Drive3.7 A sink and 4.5 A source, half bridge for two N channel MOSFETs
Supplies8 V to 17 V VDD operating, 20 V absolute maximum, UVLO inside the operating window
Timing20 ns typical propagation delay, 4 ns typical delay matching, 7.2 ns rise and 5.5 ns fall at 1000 pF
ToleranceNegative transient 28 V minus VDD on HS for under 100 ns, inputs -10 V to +20 V independent of supply
BootstrapIntegrated bootstrap diode, 120 V absolute maximum on the HB pin
GradeJunction -40 C to +150 C

Package, marking and reel data

BodyDRC, 10 pin VSON, 3.0 mm by 3.0 mm
Reel3000 pieces on a large reel, the only published packing for this code
FinishNIPDAU, level 1 at 260 C with unlimited floor life
Marking27311A on the top, TTL compatible input thresholds

Where the asymmetric drive pays

A 100 V MOSFET with 5 nanocoulombs of gate charge switches in about 15 ns with 4.5 A of source current, and the turn-off edge is set by the sink current and the gate loop inductance. Making the sink current larger shortens the turn-off but raises the switch node dv/dt, which increases the radiated emission and the stress on the bootstrap diode and the high side supply. Making the source current larger shortens the turn-on and reduces the switching loss in the channel. The 3.7 A and 4.5 A split is a practical point between the two, and it is why this part is common on 48 V to 100 V telecom rectifiers and on battery test equipment.

The bootstrap capacitor still has to be sized for the gate charge plus the high side quiescent current, and the 120 V HB rating leaves room for the switch node overshoot on a 100 V bus. A board running at 100 V with 20 percent overshoot reaches 120 V, which is exactly the rating, so a bus above 90 V should be reviewed rather than assumed. The bootstrap capacitor calculation has to include the high side quiescent current as well as the gate charge, because a 3.7 A sink and 4.5 A source part holds the switch node for longer than a smaller driver and the capacitor discharges further. Our power management cross reference page lists the codes we hold for this bus class.

Buyer questions on the UCC27311ADRCR

Is this a drop-in for the UCC27311? The A revision adds the wider negative transient tolerance and the tighter timing. The body and the pinout are the same family, but the A suffix has to be quoted explicitly because the earlier row is what appears on older approved vendor lists.

Can the driver run from a 5 V rail? No, the operating range starts at 8 V and the UVLO sits inside that window. A 5 V rail needs a different driver.

What is the 28 V minus VDD figure? It is the absolute negative excursion the HS pin survives for less than 100 ns. At a 12 V supply that is minus 16 V, which is a transient rating rather than a steady state operating point.

Availability and cross reference

The code ships 3000 pieces per reel at level 1 with unlimited floor life. Because the A revision is the row with the wider negative tolerance, we quote the full suffix and note the difference on the quotation, since a customer moving from the earlier part will see a different surge result on the same board. Our how to verify a drop in replacement page describes the bench sequence that settles whether the substitution holds.