UCC27211AQDDARQ1
Product Specifications
UCC27211AQDDARQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC27211AQDDARQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC27211AQDDARQ1: a 120 V half bridge gate driver with 3.7 A of source current, 4.5 A of sink current and a 20 ns typical propagation delay, in an eight pin SO PowerPAD body with the automotive suffix on the catalogue entry
UCC27211AQDDARQ1 is a high side and low side driver with an on-chip bootstrap diode, a switch node rated to 120 V, inputs that tolerate minus 10 V and a fully symmetric lockout so both channels shut down together in a SO PowerPAD body of 8 pins. The DDA body is the eight pin SOIC with an exposed thermal pad underneath, electrically tied to the logic ground, and the part exists because a bridge on a 48 V or a 96 V rail needs a driver that survives the negative spike at every commutation without an external clamp.
Order code and package
| Catalogue string | UCC27211AQDDARQ1, where DDA is the eight pin SO PowerPAD body, R is the 2500 piece large reel and Q1 is the automotive grade on the catalogue entry |
| Body | SO PowerPAD, DDA, eight pins with an exposed pad that is electrically the logic ground and thermally the main path out of the die |
| Reel | 2500 pieces on a large tape and reel on the DDA rows of the industrial document, with the same body also listed at 3000 on some rows |
| Finish and moisture | NIPDAU or NIPDAUAG on the DDA rows at level 1, 260 C, unlimited floor life, which removes the bake step that level 3 parts need |
| Temperature | minus 40 to 140 C junction on the DDA rows, printed alongside rows that stop at 150 C, so the exact order code decides the grade |
| Marking | 27211 on the body, with the die revision letter carried in the lot code rather than on the top mark |
| Document | SLUSAT7H, November 2011, revised September 2025 |
| Status | the Q1 suffix is not printed in this addendum; the industrial DDA rows are Active, and the automotive grade has its own document and order codes, which is stated on the page rather than glossed over |
Electrical parameters that decide the application
| Switch node rating | 120 V of maximum bootstrap voltage, with 115 V of absolute maximum on the switch node and a negative capability of minus 14 V, which is what survives the commutation spike |
| Output current | 3.7 A peak source and 4.5 A peak sink, with 7.2 ns rise and 5.5 ns fall into a 1000 pF load |
| Bias range | 8 V to 17 V of recommended supply with 20 V absolute maximum, so a 12 V rail is the natural operating point and 15 V is inside the rating |
| VDD lockout | rising at 6.2 V minimum, 7.0 V typical and 7.8 V maximum, with 0.5 V of hysteresis, so a 12 V rail starts the part with margin |
| Bootstrap lockout | rising at 5.6 V, 6.7 V and 7.9 V, with 1.1 V of hysteresis, and it disables the high side only |
| Input range | minus 10 V to 20 V on the input pins independent of the supply, with a 1.2 to 1.9 V low threshold, a 2.3 V typical high threshold and 0.7 V of hysteresis |
| Input impedance | 68 kOhm of pull down on each input, which holds an open input low and has to be accounted for when a controller output goes high impedance |
| Propagation delay | 20 ns typical in both directions, with 4 ns of matching between the two channels and 1 ns of channel to channel skew in the timing table |
| Bootstrap diode | on chip, with 0.65 to 0.85 V of forward drop at 100 uA, 0.9 to 1.05 V at 100 to 160 mA and 0.3 to 0.85 Ohm of dynamic resistance |
| Negative input handling | minus 10 V on the inputs, which allows a direct connection to a gate drive transformer secondary without a rectifier diode |
| Thermal | the exposed pad is the thermal path, so the junction to ambient figure depends on the copper under the part rather than on the body alone |
| Lockout symmetry | the two channels share one lockout reference, so a brownout turns both switches off together instead of leaving the bridge half driven |
Family variants and how they differ
| UCC27211, the industrial grade | the same silicon without the automotive suffix, for a product that does not need AEC-Q100 qualification |
| UCC27211A, the A revision | the silicon this catalogue entry refers to, with TTL thresholds only, since the pseudo CMOS input mode was removed in the A revision |
| UCC27282 | a 120 V part with 3 A of drive, cross conduction protection, an enable pin in the DRC body and a 5 V lockout, for a logic level bridge |
| The DRM and DPR bodies | the same die in an eight pin and a ten pin SON, both 3000 pieces to a reel, for a board that needs the smaller outline |
| Against a driver without a bootstrap diode | one component fewer and one less forward drop in the bootstrap path, at the cost of a diode that cannot be upgraded for a higher bus |
| Against an isolated driver | no barrier, but no propagation delay through an isolation stage and no common mode immunity requirement |
Points to check before this part goes on a BOM
The negative voltage tolerance is the specification that sells this part and the one most often taken for granted. The inputs handle minus 10 V and the switch node handles minus 14 V, both absolute maximum figures that exist because a bridge with a fast diode produces a negative spike at every commutation. A driver rated at minus 5 V will work on a bench with a resistive load and fail in a product with a real di/dt, and the failure looks like a driver that dies on the first heavy load rather than a driver that was specified wrong. The Q1 automotive rows carry the same numbers, which is the reason the part is used in 48 V systems.
The bootstrap diode is inside the package and it cannot be upgraded, which is a decision worth understanding before the bus voltage is fixed. Its forward drop is 0.9 to 1.05 V at 100 to 160 mA and its dynamic resistance is 0.3 to 0.85 Ohm, so at a 1 A recharge current the drop is around 1.5 V and the bootstrap capacitor charges to the supply minus that. On a 12 V rail that leaves 10.5 V, which is above the 6.7 V lockout and comfortable. On an 8 V rail the same arithmetic leaves 6.5 V, which is below the lockout, and the high side never starts. A board that runs this part at the bottom of its supply range has to check the bootstrap voltage rather than the rail.
Symmetry of the lockout is a small feature with a large consequence. Both channels share one reference, so a supply that sags turns both switches off at the same moment. A driver with independent lockouts can turn the high side off while the low side stays on, which puts the full bus across the low side switch and the transformer, and the resulting current is limited only by the winding resistance. In a bridge that is a destructive event rather than a glitch, which is why the symmetric behaviour is listed as a feature rather than a detail.
The 68 kOhm pull down on each input holds an open input low, which is the safe state, and it is not a discharge path for a long trace. A controller that goes high impedance during reset leaves the input to be pulled down through 68 kOhm, and with 100 pF of trace capacitance the time constant is 6.8 us, which at 100 kHz is most of a period. The usual fix is a 10 kOhm resistor at the driver pin, and the second fix is to keep the trace short. On a bridge, one bad pulse during a reset can be the difference between a product that restarts cleanly and one that needs a new pair of switches.
The A revision removed the pseudo CMOS input mode, so the thresholds are TTL only, at 2.3 V typical for a high and 1.6 V typical for a low with 0.7 V of hysteresis. That is good news for a 3.3 V controller and a problem for a 2.5 V one, because the 2.3 V typical high threshold plus the tolerance can sit above what a 2.5 V logic output guarantees. A board that drives the part from a 2.5 V FPGA bank has to check the driver's threshold against the FPGA's VOH rather than against its supply, and the fix is a level shifter rather than a different resistor.
The 4 ns of delay matching and the 20 ns typical delay are what make this part usable at a few hundred kilohertz. At 300 kHz a period is 3.3 us, and 4 ns of mismatch is 0.12 per cent of it, so 50 ns of dead time covers the mismatch with room for the switch's own turn off. At 1 MHz the same 50 ns is 5 per cent of a period and starts to cost efficiency, and the honest answer at that frequency is a driver with a shorter delay rather than a smaller dead time. The part's 125 ns maximum delay is what limits the frequency in practice, because the dead time has to be set from the maximum rather than the typical.
The Q1 suffix and what the industrial document does not say
The document on this page is the industrial UCC27211 revision, and its addendum does not print a row for UCC27211AQDDARQ1. The automotive grade has its own document and its own orderable table, and the honest position is that the automotive grade must be confirmed against that document or against a vendor confirmation before a production order is placed. The industrial DDA rows are active and print 2500 pieces on a large reel with a level 1 moisture rating, and those are the rows this page can quote.
The catalogue string also carries an A that refers to the silicon revision rather than to a separate family. The A revision is the one whose inputs are TTL only, and the revision history records the removal of the pseudo CMOS mode. A customer comparing this entry against a UC27211 from a decade ago is comparing two different input structures, and the A on the end of the string is the only clue on the order.
Where a 120 V driver stops and a 600 V part begins
A 48 V or 96 V rail with a commutation spike of 40 V sits comfortably inside the 120 V bootstrap rating and the minus 14 V switch node capability, and this part is the right size for it. A 400 V bus is outside the rating by a factor of three, and the negative spike on a fast bridge at that voltage needs the 600 V family. The boundary is not the nominal bus but the spike, and the spike is set by the loop inductance and the current slope rather than by the supply.
The other boundary is isolation. This part has no barrier, so the high side floats on the switch node and the controller shares a ground with the low side. A product that needs the controller isolated from the power stage, which is common when the controller has a user connection, needs an isolated driver instead. Recognizing that early avoids a board that works but cannot pass a safety review.
Where this order code fits
This is the driver for a synchronous buck, a half bridge or a full bridge on a 48 V or a 96 V rail, in a telecom rectifier, a battery charger, a class D amplifier or a 48 V motor drive Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Is the bootstrap diode external? No. The diode is on the die, so the bootstrap capacitor is the only external part. The diode's forward drop is 0.9 to 1.05 V at 100 to 160 mA and it cannot be upgraded for a higher bus.
Can it run from a 12 V rail? Yes. The lockout releases at 7.0 V typical and the recommended range is 8 V to 17 V, so 12 V is the natural operating point.
Why does the switch node rating matter more than the bus? Because the commutation spike adds to the bus, and the minus 14 V capability is what keeps the high side alive during the spike. A driver rated at minus 5 V works on a bench and fails on a real load.
Is this part automotive qualified? The catalogue string carries Q1, and the industrial addendum on this page does not print that row. Confirm the automotive grade against its own document or a vendor confirmation before ordering.
What dead time should be used? The delay is 20 ns typical with 4 ns of matching, so 50 ns of dead time covers the mismatch plus the switch turn off at a few hundred kilohertz.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.