Contact Us

UCC256403ADDBR

Brand: Texas Instruments
Texas Instruments UCC256403ADDBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC256403ADDBR — Power Management & Signal Chain | Superb Automation

UCC256403ADDBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC256403ADDBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC256403ADDBR: LLC resonant controller with burst mode and an integrated high side driver

UCC256403ADDBR is a resonant LLC controller with a hybrid hysteretic control loop in a SOIC body of 14 pins. It pairs with a power factor correction front end to build an offline supply, drives the two LLC switches from an integrated high side driver rated 0.6 A source and 1.2 A sink, and handles burst mode with soft entry and soft exit so a charger stays quiet at no load. The A suffix is one of the feature variants in a six row comparison table, and this order code ships 2500 pieces on a large reel.

Order code and package

UCC256403ADDBRDDB body, SOIC-14, 2500 pieces on a large reel, active in the addendum revised August 2026
UCC256403ADDBTthe same body at 250 pieces on a small reel, active
UCC256403DDBRthe plain string without the A, also active at 2500 pieces
UCC256404BDDBRthe latch off member, active at 2500 pieces

Electrical parameters that decide the application

Gate drive0.6 A source and 1.2 A sink into the two LLC switches, high side driver integrated
Control lawhybrid hysteretic control with a fast exit from burst mode
Dead timeadaptive, set by the controller rather than by an external resistor
Burst modesoft on and soft off periods, with a user option to disable burst mode
Protectionover temperature, output over voltage, input under voltage and three levels of over current
SupplyVCC 13 V to 26 V recommended, RVCC output capped at 17 V and 100 mA
RVCC decoupling4.7 uF on the RVCC pin
Pin limitsBLK, LL/SS and VCR to minus 0.55 V below ground and 7.2 V above, VCC to 30 V absolute
Junction and ambientminus 40 to plus 125 C

Family variants and how they differ

UCC256402 and 402Abase and A variants in the same DDB body, active at 2500 and 250 packing
UCC256403 and 403Athe row on this page, active at 2500 large reel and 250 small reel
UCC256404, 404A and 404Bthe members that differ in the feature rows of the comparison table, including a latch off version
Automotive and other bodiesthe family is printed in DDB only, and the automotive strings have their own document

Points to check before this part goes on a BOM

Burst mode is the reason this controller exists in a charger. The burst level and the hysteresis are programmed through the VCR pin, and the soft on and soft off periods keep the transformer from ticking audibly at no load, which is the failure mode that most LLC controllers show at low power.

The comparison table in the document separates the six rows on three blocks: whether the high voltage startup is integrated, whether the active X capacitor discharge is integrated, and whether an external bias supply is required. The burst soft on and off column and the restart or latch behaviour are separate again. Read the row before substituting one suffix for another, because the pinout is the same and only the table tells them apart.

The hybrid hysteretic control is what gives the fast transient response. Conventional LLC controllers move the switching frequency slowly because the loop is compensated for a narrow band, and this one leaves burst mode quickly enough that a load step does not collapse the output rail.

The ZCS avoidance scheme is a protection, not a feature to tune. If the converter drifts into the capacitive region the body diodes of the switches recover hard, and the controller shifts the operating point instead of letting that happen.

Both the plain and the A string are active at 2500 pieces on a large reel, so a purchasing change from one to the other does not need a reel change. What changes is the feature row, so the substitution has to be checked against the circuit rather than against the packing.

The 4.7 uF on the RVCC pin is not optional decoupling. The internal regulator sources up to 100 mA and the gate drive pulls current in bursts at the switching frequency, so the capacitor is the local reservoir that keeps the rail from collapsing on every edge. A 1 uF part that looks adequate on a bench supply will show up as jitter in the dead time on a real board.

The BLK, LL/SS and VCR pins are limited to minus 0.55 V below ground and 7.2 V above, which is a narrow window compared with the supply. Those pins carry the bulk sense divider, the soft start capacitor and the burst threshold, so a divider that is copied from a part with a wider input range can sit outside the window at high line and clamp the sense signal instead of reading it.

The 26 V recommended maximum on VCC is 4 V below the 30 V absolute rating, and the difference is the room for the spike that appears when the PFC stage ahead of the LLC switches. A board that runs the bias at 24 V has 2 V of margin in the recommended window and 6 V to the stress rating, which is a workable position; one that runs at 26 V has none.

Where the 2500 piece reel comes from

The addendum prints 2500 large reel and 250 small reel for every DDB body in the family, and the tape dimensions are the same across the suffixes, so a prototype run taking 250 pieces and a production run taking 2500 use the same part with different packing. The reel diameter and the pocket size do not change between them.

The gate drive figure of 0.6 A source and 1.2 A sink is deliberately modest. An LLC switch is a small die compared with a hard switched bridge, so the gate charge is low and a large peak current would only ring the gate loop. The asymmetric source and sink is there to turn the device off faster than it turns on, which is what the dead time calculation assumes.

Why burst mode needs soft edges rather than a simple skip

A controller that stops switching and restarts at full duty produces an audible tick at the repetition rate, because the transformer sees a step of magnetising current each time. The soft on and soft off periods ramp the burst envelope, which spreads that energy and keeps the tick below the noise floor of a bedroom at night, and that is the measurement a television or monitor customer actually makes.

The burst power level is set by the VCR divider, and the same pin sets the initial voltage at startup. That shared function is the reason the startup sequence in the document is described in terms of the divider rather than in terms of a separate soft start ramp: the two behaviours come from one network and have to be chosen together.

Where this order code fits

Television and monitor supplies, lighting drivers, AC to DC adapters, power tools, medical power supplies, printers and projectors are the applications the document lists, and all of them need low standby power with no audible noise. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does the controller include the high side driver? Yes. Both gate outputs are integrated, 0.6 A source and 1.2 A sink, so no external driver is needed for the two LLC switches.

Can burst mode be turned off? Yes. The document states a user option to disable burst mode, which is what a product does when the light load efficiency target is looser than the noise target.

Is the A suffix the same die as the plain string? It is a feature variant in the same DDB body and it is active at the same reel sizes. The comparison table is where the difference is stated, so the substitution has to be checked there.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.