UCC23513DWYR
Product Specifications
UCC23513DWYR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC23513DWYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC23513DWYR: a single channel isolated gate driver with a 5.7 kVRMS reinforced barrier, 4.5 A of source current and a 105 ns maximum propagation delay, in a stretched six pin SOIC on an 850 piece reel
UCC23513DWYR is an isolated gate driver whose input is an emulated diode rather than an LED, so the input side ages like silicon instead of like an optocoupler, and whose output stage delivers 4.5 A source and 5.3 A sink from a rail up to 33 V in a SOIC body of 6 pins. The DWY body is a stretched six pin SOIC measuring 7.50 mm by 4.68 mm with more than 8.5 mm of creepage, and the part exists because an optocoupler gate driver ages, drifts and cannot hold a 105 ns delay over ten years of switching.
Order code and package
| Catalogue string | UCC23513DWYR, where DWY is the stretched six pin SOIC and R is the 850 piece large reel |
| Body | SOIC, DWY, six pins, 7.50 mm by 4.68 mm with more than 8.5 mm of creepage and clearance across the barrier |
| Reel | 850 pieces on a large tape and reel, which is smaller than the 2500 or 3000 used by most parts in this family |
| Finish and moisture | NIPDAU plating, with the plain row printing Call TI in the moisture column while the .A row of the same string prints level 2 at 260 C and one year |
| Temperature | minus 40 to 125 C on every row, with the electrical table specified to 150 C junction |
| Marking | UCC23513 on the body; the 8 V lockout member is marked UC23513B and is a different order code |
| Document | SLUSD31F, October 2018, revised July 2026 |
| Status | Active and in production on the addendum dated 8 June 2026 |
Electrical parameters that decide the application
| Isolation rating | 5.7 kVRMS reinforced, with 8000 VPK of maximum transient voltage, 2121 VPK repetitive peak and 1500 VRMS of working voltage per VDE 0884-11 |
| Barrier geometry | more than 8.5 mm of external creepage and clearance, more than 17 um of distance through the insulation and a tracking index above 600 |
| Output current | 3 A minimum and 4.5 A typical source, 3.5 A minimum and 5.3 A typical sink, measured into a 180 nF load with 10 us pulses |
| Supply range | 15 V to 30 V of recommended output supply with 33 V absolute maximum, so a 15 V rail with a minus 5 V negative bias fits inside the rating |
| Lockout, 12 V version | rising at 11 V minimum, 12.5 V typical and 13.5 V maximum, falling at 10 V, 11.5 V and 12.5 V, with 1 V of hysteresis |
| Lockout, B version | rising at 7.8 V, 8.5 V and 9.2 V, falling at 7.05 V, 7.75 V and 8.45 V, with 0.75 V of hysteresis |
| Propagation delay | 70 ns minimum and 105 ns maximum in both directions, with 25 ns of pulse width distortion and 35 ns of part to part skew |
| Input stage | an emulated diode with a 1.5 to 4 mA forward threshold, 1.8 to 2.4 V of threshold voltage and a recommended forward current of 7 to 16 mA |
| Reverse handling | 15 V of reverse breakdown on the input, with 13 V of reverse polarity handling so an interlock or a bipolar drive does not damage the input |
| Common mode immunity | 150 kV per microsecond minimum in both output states, measured at 1500 V of common mode |
| Output edges | 28 ns rise and 25 ns fall into a 1 nF load, with 20 to 30 us of recovery after the lockout releases |
| Thermal | 126 C per W junction to ambient in the six pin body, with 66.1 C per W junction to case |
Family variants and how they differ
| UCC23513, the part on this page | 12 V lockout, 5.7 kVRMS reinforced, 4.5 A source, the choice for an IGBT or a silicon carbide FET driven from a 15 V rail |
| UCC23513B | the same die with an 8 V lockout, so a 12 V rail can drive a logic level FET without the driver sitting in lockout |
| UCC23313 in the same family | 3.75 kVRMS basic insulation and a 5300 VPK transient rating, the lower grade for a product that only needs basic insulation |
| The -Q1 rows | the automotive grade has its own document and its own order codes, so a bill of materials line that needs AEC-Q100 has to name it rather than assume the suffix |
| Against an optocoupler driver | 105 ns maximum against several hundred nanoseconds, 25 ns of distortion against a spread that grows with age, and an insulation life quoted above 50 years |
| Against a digital isolator plus a driver | one body instead of two, at the cost of an input that needs current rather than a logic level |
Points to check before this part goes on a BOM
The input is an emulated diode, which is the point of the part and also the thing that catches people out. An optocoupler input is an LED that needs a resistor and degrades as the LED dims. Here the input is a silicon structure that behaves like a diode with a 2.1 V threshold and a 1.5 to 4 mA trip window, so the drive is built the same way, with a series resistor from the controller, but the current does not have to be derated for ageing. A controller that can only source 2 mA will not reliably turn the part on, and the fix is a buffer rather than a smaller resistor.
The 850 piece reel is the detail that decides a prototype schedule. Most parts in this family ship 2500 or 3000 to a reel, and a distributor that quotes from a catalogue will often assume the larger figure. A first article build of 200 pieces needs a partial reel or a cut tape, and a production line that plans on 3000 per reel will be short on the first order. The order code ends in R, which is the large reel for this body, so there is no smaller reel option to fall back on.
Two lockout versions exist and they are not interchangeable on a 12 V rail. The 12 V version starts at 12.5 V typical and will sit in lockout on a 12 V rail that sags, which is what you want for an IGBT that needs 15 V of gate drive. The B version starts at 8.5 V typical and is the one to use when the rail is 12 V and the FET is a logic level device. Fitting the 12 V version to a 12 V rail produces a driver that works on the bench at 12.6 V and fails when the rail drops under load, and the marking on the body is the only way to tell the two apart after they are separated from the reel.
The 150 kV per microsecond common mode immunity is the number that matters in a motor drive, and it is specified at 1500 V of common mode rather than at the full isolation rating. A half bridge switching 600 V in 20 ns produces a dv/dt that couples through the barrier capacitance and pushes current into the input side, and a driver with 50 kV per microsecond will produce output glitches at every edge. The 150 kV figure is what keeps the output quiet, and it is worth more than the isolation rating on a fast silicon carbide stage.
Power dissipation is dominated by the gate charge, not by the quiescent current. The output supply current is 2.2 mA with the diode on and 2 mA with it off, which is negligible, while driving a 200 nC gate at 20 kHz at 15 V is 60 mW of gate charge plus the driver's own loss. In a 126 C per W body that is 8 C of rise, which is fine, and at 100 kHz with a larger gate the same arithmetic gives 40 C of rise, which is the point at which the ambient derating in a sealed enclosure has to be checked rather than assumed.
The reinforced rating is certified to VDE 0884-11 with an 8000 VPK transient and a 2121 VPK repetitive peak, and the working voltage is 1500 VRMS. Those are three different numbers for three different tests, and the one that governs a product's life is the working voltage. A board that quotes 5.7 kVRMS in a specification but runs the barrier at 1500 VRMS continuously is inside the rating; one that runs it at 2000 VRMS is outside the working voltage while still passing a hipot, and the failure mode is a slow one that appears in the field rather than on the line.
What the driver has to be told about the gate
The peak current is 4.5 A source and 5.3 A sink, and the gate resistor is chosen from the gate charge rather than from the peak current. A 200 nC gate switched in 100 ns needs 2 A, which is inside the rating with margin, and a 20 Ohm resistor at 15 V gives 750 mA and a 267 ns edge. The reason to use a resistor at all is ringing: the loop inductance between the driver and the gate, plus the gate capacitance, forms a resonant circuit, and a driver with a 1.45 Ohm pull up will excite it at tens of megahertz if the loop is long. The resistor is the damping, and the diode in parallel is what keeps turn off fast.
The negative bias is the other half of the drive. The output supply can sit at 33 V absolute maximum, so 15 V positive with minus 5 V on the emitter is 20 V of total supply and well inside the rating, and it is the arrangement that keeps a silicon carbide FET off during a fast dv/dt on the drain. Without the negative rail the FET turns on through its own Miller capacitance at every edge, and no amount of gate resistance fixes that because the current is coming from the drain rather than from the driver.
Where a 5.7 kVRMS driver stops being the right part
A basic insulation requirement is satisfied by the 3.75 kVRMS member of the same family and the cost difference is real on a product that builds thousands of units. The decision is made by the end product standard rather than by the switching voltage: a 400 V motor drive with a floating gate driver needs functional or basic insulation depending on the earthing, and a medical product with a patient connection needs two means of protection. The part on this page covers the reinforced cases at working voltages up to 1500 VRMS.
Above that voltage the answer is a different family rather than a different suffix. A 1700 V silicon carbide module on a 690 V bus needs a driver with a higher working voltage and a longer creepage, and the six pin stretched body does not have the room for it. Recognizing that limit early avoids a board respin at the safety review stage, which is the most expensive place to discover it.
Where this order code fits
This is the gate driver in a motor drive, a solar inverter, an uninterruptible supply or an induction heating stage, wherever a high side or a floating FET has to be driven from a controller that sits on a different ground Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Does it need a separate isolated supply? Yes. The driver isolates the signal, not the power. The output side needs a 15 V to 30 V bias supply referenced to the emitter of the switch.
What input current does it need? Between 7 mA and 16 mA of forward current, with a 1.5 to 4 mA turn on threshold. A controller that sources less than about 4 mA needs a buffer.
Can the 12 V version run from a 12 V rail? No. It needs 12.5 V typical to start. The B version with the 8 V lockout is the part for a 12 V rail.
What is the difference between 5.7 kVRMS and 1500 VRMS? 5.7 kVRMS is the one minute withstand per UL 1577, and 1500 VRMS is the continuous working voltage per VDE 0884-11. The working voltage is the one that governs life.
Why is the reel only 850 pieces? That is the published packing for the stretched six pin body. There is no 3000 piece reel for this order code, so a production order needs the reel size named.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.