UCC23511DWYR
Product Specifications
UCC23511DWYR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC23511DWYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC23511DWYR: optically compatible isolated gate driver in the stretched SO-6 body
UCC23511DWYR is a single channel isolated gate driver with an emulated diode input in a stretched SO body of 6 pins. It replaces an optocoupler gate driver without a board change while using an emulated diode on the input instead of an LED. The output side runs up to 33 V, delivers 1.5 A source and 2 A sink, and the barrier is rated 5.7 kVRMS with more than 8.5 mm of creepage in the stretched body. This order code is the 12 V lockout version.
Order code and package
| UCC23511DWYR | 12 V lockout version, stretched SO-6, 850 pieces on a large reel, active |
| UCC23511BDWYR | 8 V lockout version, same body and same 850 piece reel, active |
| UCC23511DWY and UCC23511BDWY | the tube rows are marked obsolete in the current addendum |
| UCC23511 Q1 | the automotive member is a separate qualification document |
Electrical parameters that decide the application
| Peak output current | 1.5 A source and 2 A sink |
| Output supply | 33 V maximum, 14 V to 33 V recommended on this 12 V lockout member |
| Propagation delay | 105 ns maximum |
| Pulse width distortion | 35 ns maximum, part to part skew 25 ns maximum |
| Common mode transient immunity | 150 kV per us minimum |
| Isolation | 5.7 kVRMS for one minute per UL 1577, 8000 V peak reinforced per VDE 0884-11, barrier life over 50 years |
| Creepage and clearance | over 8.5 mm in the stretched body, mould compound tracking index above 600 V |
| Input reverse polarity | 13 V handling on the input stage |
| Junction temperature | minus 40 to plus 150 C |
Family variants and how they differ
| 12 V lockout | the string on this page, used where the gate drive sits at 15 V and the emitter or source node moves with it |
| 8 V lockout | the B string, for a lower gate voltage rail, same footprint and same reel size |
| Tube packing | both tube rows are obsolete, so only the reel rows are current |
| Automotive | the Q1 string carries its own qualification and its own addendum |
Points to check before this part goes on a BOM
The input is an emulated diode rather than an LED. That removes the current transfer ratio drift that forces an engineer to overdrive an optocoupler at end of life, and the vendor states the barrier life as more than 50 years instead of quoting a degradation curve.
The 33 V output supply is what allows a bipolar gate drive, for example plus 15 V on the gate and minus 8 V on the source, which is the arrangement that keeps an IGBT or a SiC MOSFET off through a fast dv/dt event.
The lockout number has to match the rail. The 12 V member on this page is recommended from 14 V, so a 12 V auxiliary rail sits below the recommended floor even though it is above the lockout itself, and the outputs can be clamped low for more than 20 us when the supply dips under the threshold.
Common mode transient immunity is 150 kV per us minimum and the propagation delay is 105 ns maximum, not typical. Both figures are the ones a motor drive or a solar inverter has to meet when the switching node slews in a few tens of nanoseconds.
The stretched body gives more than 8.5 mm of creepage and clearance, which is what makes the part usable on a high DC bus without potting, and the mould compound has a tracking index above 600 V so the surface does not carbonise along the barrier.
The 850 piece reel is a real constraint on a small production run. It is a full reel, not a partial, so a build of 200 pieces either buys a reel and carries the balance or buys through a distributor who breaks the reel and adds a handling charge. That is a purchasing question rather than an electrical one, but it is the question that decides the quoted price.
The emulated diode input draws a forward current like an LED but the threshold does not degrade, so the drive resistor can be sized for the middle of the current window rather than the end of life. On a 10 year product that is the difference between a gate drive that still switches at the specified speed and one that has to be overdriven from the first day to stay inside the timing budget.
The 150 kV per us figure is a minimum, not a typical. It is measured with a specific test circuit in the document, and the number that a board actually achieves depends on the stray capacitance across the barrier, which is why the board section spends its space on keeping the two sides apart rather than on copper area.
Where the pin for pin claim actually holds
The input side accepts an optocoupler footprint and the output side keeps the same gate resistor and capacitor arrangement, so a board can be reworked without a board change. What changes is the input drive: an emulated diode needs a forward current like an LED but does not age the same way, so the series resistor sized for an optocoupler at end of life usually stays and the drive margin improves.
Reverse polarity on the input stage is rated to 13 V, which covers the case where the anode is pulled below the cathode by the return current of a fast switching loop. That is the failure mode that turns an optocoupler into a short after a few thousand hours, and it is stated as a rating rather than left to the application note.
What the two lockout versions change in a bill of materials
The 12 V and 8 V rows share a body, a footprint and a reel size, so a change between them costs nothing in tooling and nothing in handling. What changes is the auxiliary winding that feeds the output side: a 12 V gate drive needs a bias rail that stays above 14 V, and an 8 V part can run from a rail that would trip the other version into lockout on every brownout.
The bipolar arrangement that the 33 V rating enables is worth spelling out. A plus 15 V rail turns the switch on and a minus 8 V rail holds it off, which is 23 V of gate swing and 15 V of steady state gate stress. The 33 V absolute maximum covers the sum plus overshoot, so an engineer who runs plus 15 and minus 15 is 3 V from the rating before any ringing is counted.
Where this order code fits
Industrial motor drives, industrial power supplies and UPS, solar inverters and induction heating are the four applications the vendor names, and each of them puts the driver on a node that slews hard. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Can it drive a SiC MOSFET? Yes. The 33 V output supply and the 1.5 A source and 2 A sink are sized for the gate charge of a SiC part, and the 12 V lockout member suits a 15 V gate drive with a negative off bias.
Does the input need the same resistor as an optocoupler? It needs a forward current like an LED, so the same style of series resistor applies, but the threshold does not drift with age the way a current transfer ratio does.
What is the isolation rating in numbers? 5.7 kVRMS for one minute per UL 1577 and 8000 V peak reinforced per VDE 0884-11, with a declared barrier life above 50 years.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.