UCC21550CDWKR
Product Specifications
UCC21550CDWKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC21550CDWKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC21550CDWKR: the 12 V UVLO member of a 5 kV dual channel driver family
The UCC21550CDWKR is a reinforced isolation dual channel gate driver that can be wired as two low side drivers, two high side drivers or a half bridge. It drives 4 A peak source and 6 A peak sink into MOSFET, silicon carbide, GaN or IGBT gates, holds a 5 kVRMS barrier with more than 125 volts per nanosecond of common mode transient immunity, and quotes 33 ns typical propagation delay with 5 ns maximum pulse width distortion. The C in the order code is the 12 V UVLO option, which is the variant an IGBT bridge uses when the gate drive rail is 15 V and the part has to stay off until that rail is genuinely valid.
The junction range is minus 40 C to plus 150 C, which is 25 C wider than the earlier UCC2154x family and is the reason this part turns up in automotive HVAC and on board charger builds where the driver sits near the heat. The input side takes a wide logic supply, the output side runs to 25 V, and every supply has its own UVLO. Dead time is set by a resistor, the disable pin shuts both outputs, and an integrated de-glitch filter rejects input transients shorter than 5 ns so a coupled spike on the PWM line does not become a gate pulse.
Key electrical data for the UCC21550CDWKR
| Drive | 4 A peak source, 6 A peak sink, up to 25 V on the output supply |
| Timing | 33 ns typical propagation delay, 5 ns maximum pulse width distortion, 10 microseconds VDD power-up delay |
| Isolation | 5 kVRMS barrier, CMTI above 125 V per nanosecond, reinforced rating per the family document |
| UVLO | 5 V, 8 V and 12 V options; the C suffix is the 12 V row on a 9.2 V recommended minimum |
| Supplies | VCC quiescent 4.2 mA typical and 4.8 mA maximum, VDDx 1.5 mA typical and 2.5 mA maximum, VCC UVLO rises at 2.7 V |
| Grade | Junction -40 C to +150 C, de-glitch filter rejects transients shorter than 5 ns |
Package, marking and reel data
| Body | DWK, 14 pin SOIC, thin body, 3.3 mm channel to channel spacing option in the family |
| Reel | 2000 pieces on a large reel, 353 mm reel diameter and 16 mm carrier in the tape drawing |
| Finish | NIPDAU, level 2 at 260 C, one year floor life |
| Marking | 21550C on the top, which is the only visible way to separate the 12 V UVLO row from the 5 V and 8 V rows |
Why the UVLO letter decides the part
Three UVLO options share one body and one pinout, and the marking is the only external difference. A 12 V option in a 15 V gate drive system keeps the driver off until the rail crosses 12 V, so the IGBT is not driven with a gate voltage that is high enough to turn it partly on but too low to switch it cleanly. A 5 V option in the same socket would enable at a third of the rail and leave the device in the linear region during every power-up, which is a reliability problem that shows up as a rising junction temperature rather than an immediate failure.
The second selection point is the dead time resistor. The family table maps resistance to dead time, and the part spread on top of the resistor tolerance is what the bridge has to survive. A 1 percent resistor and a dead time margin of 100 ns above the calculated minimum is the pattern that works on a 20 kHz IGBT bridge; a 200 kHz silicon carbide bridge needs the smaller dead time the same table allows and a tighter resistor. Our power management cross reference page lists the isolated drivers we hold in this class.
Buyer questions on the UCC21550CDWKR
How do I tell the 12 V UVLO row from the 5 V row in stock? By the marking, 21550C against 21550A or 21550B, and by the order code suffix. The bodies are identical, so a lot that arrives without its reel label cannot be separated by inspection.
Can this part drive a silicon carbide half bridge at 100 kHz? Yes, the 33 ns propagation delay and 5 ns pulse width distortion support it, but the dead time has to be set for the device rather than copied from a silicon IGBT bridge, and the common mode transient immunity of 125 volts per nanosecond is the number to check against the switch node slew.
Does it need a negative gate bias? It does not provide one. The driver swings between VDD and the source or emitter node, so a negative bias requires an external arrangement rather than this part alone.
Availability and cross reference
This code ships 2000 pieces per reel with NIPDAU plating at moisture level 2. Because three UVLO options share the body, we quote the full order code rather than the family name and print the marking on the packing list. Customers who hold the older UCC2154x family in a build should note the junction range difference of 25 C before treating the two as interchangeable, and our how to verify a drop in replacement page sets out the checks that settle it in one bench session.