Contact Us

UCC21330CQDRQ1

Brand: Texas Instruments
Texas Instruments UCC21330CQDRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

UCC21330CQDRQ1 — Power Management & Signal Chain | Superb Automation

UCC21330CQDRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The UCC21330CQDRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

UCC21330CQDRQ1: an isolated dual channel gate driver with 4 A of source and 6 A of sink current, 3 kVRMS of isolation, programmable dead time and a 12 V output lockout, in the sixteen pin SOIC on a 3000 piece reel

UCC21330CQDRQ1 is a dual channel driver that can be wired as two low side drivers, two high side drivers or a half bridge, with the dead time set by a resistor rather than by the controller, and with the two output supplies isolated from the input side in a SOIC body of 16 pins. The D body is the sixteen pin SOIC and the C in the order code selects the 12 V output lockout, which is the version for IGBT and for silicon carbide switches that need a gate swing near 15 V.

Order code and package

Catalogue stringUCC21330CQDRQ1, where 21330 is the device, C is the 12 V lockout variant, Q is the automotive qualifier, D is the sixteen pin SOIC, R is the large reel and the closing Q1 repeats the qualification
BodySOIC, D outline, sixteen pins, with the input side and the two output drivers separated by the isolation barrier inside the package
Reel3000 pieces on a large reel on the rows the document publishes for this body
Qualification notethe document prints addendum rows for the industrial UCC21330C strings only. The automotive Q1 string on this page carries its own qualification document, so its reel, its grade and its marking have to be confirmed there rather than from this table
Finish and moistureNIPDAU at moisture level 2 for 260 C with a one year floor life
Isolation3 kVRMS between the input side and the two output drivers, with common mode transient immunity above 125 V per nanosecond
Temperatureminus 40 to 150 C junction, which is the range the switching parameters are specified over
Drive capability4 A peak source and 6 A peak sink per channel, asymmetric so the turn off is faster than the turn on

Electrical parameters that decide the application

Output supplyup to 25 V on VDD, which allows a plus 15 V and minus 5 V gate swing on an IGBT without an external regulator
Lockout options5 V, 8 V and 12 V versions of the same die, with the C suffix on this string selecting 12 V
Propagation delay33 ns typical in both directions, so the driver does not have to be accounted for separately from the controller in the dead time budget
Pulse width distortion5 ns maximum between the rising and the falling edge, which is tighter than the propagation delay spread and matters more in a half bridge
Power up delay10 microseconds maximum from the output supply reaching its threshold to the output being enabled, which is the window in which the controller must hold both inputs low
Dead timeset by a single resistor to the DT pin and applied between the two channels in half bridge configuration, so the dead time does not depend on the controller timing
Disablea disable pin shuts both outputs down together, which is the fast path for a fault that has to remove drive from both switches at once
Input filtertransients shorter than 5 ns on the input pins are rejected, so a switching node coupling into the input trace does not produce a false command
Isolation3 kVRMS for one minute, which is the level that suits a 400 V to 800 V bus with a functional barrier rather than a reinforced one
Output stagethe sink and source currents are quoted separately because the two paths are separate transistors, and the 6 A sink is what removes the gate charge before the other switch turns on
Channelstwo independent channels with their own output supplies, so a high side driver can run from a bootstrap rail and a low side driver from a fixed rail in the same package
Thermalthe junction range to 150 C allows the package to run hot in a gate drive stage that has no airflow, with the limit set by the gate charge and the frequency rather than by ambient alone

Family variants and how they differ

Half bridgethe two channels are driven from one input pair with the dead time resistor in circuit, which is the configuration that removes the dead time from the controller firmware
Two low sideboth channels referenced to the same source, used to drive two independent switches such as a synchronous buck or two parallel branches
Two high sideboth channels on their own bootstrap or isolated supplies, used in a dual switch forward or a full bridge half
Lockout variants5 V for logic level MOSFETs driven from a 5 V rail, 8 V for silicon carbide where a lower swing is wanted, 12 V for IGBT and standard MOSFET gate drive
Automotive versionthe Q1 qualifier on this string, with its own document and its own temperature grade rather than a separate die
Familythe same barrier and pinout cover a range of drive currents, so a smaller switch can be driven by a lower current member without a board change

Points to check before this part goes on a BOM

The dead time resistor is the reason to use this part rather than a plain dual driver. With the dead time inside the driver it does not change when the controller clock changes, and a firmware update cannot accidentally shorten it to the point where both switches conduct.

The C suffix is the 12 V lockout and it is not interchangeable with the 5 V or 8 V members. A 12 V part on a 5 V gate drive rail never enables, and a 5 V part on an IGBT drive rail enables at a gate voltage where the switch is only partly on, which is the failure mode that looks like a short circuit on the first pulse.

Five nanoseconds of pulse width distortion against 33 ns of propagation delay is the right way round. The distortion is what produces a DC offset in a transformer coupled stage, and 5 ns at 100 kHz is 0.05 per cent of the period, small enough that a blocking capacitor is not needed for most bridges.

The 3 kVRMS barrier is a functional isolation level, not reinforced. For a 400 V bus with a SELV controller it is adequate, but a product that has to meet reinforced isolation for a high voltage bus needs a driver with a 5.7 kVRMS barrier, and the two are not interchangeable on the same board.

The automotive string on this page is not printed in the industrial addendum. Before a purchase order, the automotive document has to confirm the reel, the marking and the grade, because an industrial row and an automotive row can differ in moisture level and in packing without any change to the part number stem.

Setting the dead time

One resistor from the DT pin to the input ground sets the interval between the two channels. The value is chosen from the vendor table for the required interval, and the interval is then fixed by the resistor rather than by the controller, which is what makes the timing repeatable across boards.

The interval has to be longer than the switch turn off time plus the driver propagation spread plus the gate resistor discharge time. On a silicon carbide half bridge at 800 V, that sum is often 150 ns to 250 ns, and a dead time set from a typical propagation delay alone leaves nothing at the corners.

Where this order code fits

Half bridge and full bridge stages in on board chargers, DC to DC converters in electric vehicles, motor drives, server and telecom power supplies, and any isolated gate drive where the two channels have to be timed against each other rather than against the controller Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Date Code Management page.

Questions buyers ask

What does the C in the part number mean? The 12 V output lockout. The family offers 5 V, 8 V and 12 V lockouts on the same die, and the letter before the package code selects which one.

Is the isolation reinforced? No, it is 3 kVRMS for one minute, which is a functional barrier. A reinforced barrier for a high voltage bus needs the 5.7 kVRMS family.

Can the two channels drive a half bridge directly? Yes. Wire them as a half bridge, connect the dead time resistor and drive the two inputs from one PWM pair, and the driver handles the interval between them.

Why is the sink current higher than the source? Because turn off has to remove the gate charge before the other switch conducts, while turn on can be slowed with a gate resistor to control the drain voltage rise. The 6 A sink sets the fastest turn off the part can produce.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.