Contact Us

TPSM82813SSILR

Brand: Texas Instruments
Texas Instruments TPSM82813SSILR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPSM82813SSILR — Power Management & Signal Chain | Superb Automation

TPSM82813SSILR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPSM82813SSILR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPSM82813SSILR: 3 A at 4 MHz in a package under 2.4 mm tall

The TPSM82813SSILR is a 3 A step-down module with a 2.75 V to 6 V input and a 0.6 V to 5.5 V output, in a 14 pin uSiL package that stands under 2.4 mm tall. The S in the code is the spread spectrum version, which sweeps the 1.8 MHz to 4 MHz switching frequency slightly to spread the emission, and the SIL body is the uSiL package with the inductor on top of the die rather than beside it. For a board that has to fit behind a connector or under a shield can, that height is the specification that decides the part.

The module is a fixed frequency peak current mode converter with a 1 percent output accuracy in PWM mode, and the frequency can be set by a resistor or locked to an external clock between 1.8 MHz and 4 MHz. The SS/TR pin does two jobs: a capacitor sets the start up ramp to limit inrush, and a voltage on the pin makes the output track another rail, which is how a 1.2 V core rail follows a 1.8 V memory rail without a sequencer part. The power good output is a window comparator, not a single threshold, so it reports an overvoltage as well as an undervoltage.

Key electrical data on the page

Input and output2.75 V to 6 V in, 0.6 V to 5.5 V out, 3 A continuous in the SIL body
Accuracy1 percent in PWM mode, with a 0.6 V reference and an external divider
Switching1.8 MHz to 4 MHz adjustable, synced to an external clock with a 40 to 60 percent duty window
No-load current15 uA typical and 21 uA maximum with the device enabled and not switching
Power good95 percent rising and 90 percent falling for undervoltage, 110 percent and 107 percent for overvoltage
Start upSS/TR source current 2.5 uA, 200 us delay from enable to the first switch pulse
Thermalthermal shutdown at 170 C with 15 C of hysteresis, so a hot board recovers by itself

Package, marking and reel data

BodyuSiL SIL, 14 pins, 3.3 mm by 4.3 mm tape pocket, under 2.4 mm tall with the inductor on top
Reel3000 pieces on a 178 mm reel, 13.2 mm carrier, 8 mm pitch, quadrant Q1
PocketA0 3.30 mm, B0 4.30 mm, K0 2.60 mm, carrier width 12.0 mm
Finish and moisturenickel gold, level 2 at 260 C, one year floor life
Marking and gradeHF on the top, rated -40 C to 125 C junction

Where a 4 MHz module with spread spectrum fits

Telecom line cards, test and measurement instruments and medical monitors all share a requirement: a 3.3 V or 1.8 V rail close to the load, on a board with a shield can over the analog section, and a height budget that rules out a conventional inductor. A 4 MHz switching frequency keeps the ripple small with a 22 uF output capacitor and puts the fundamental above the band where most analog front ends care, and the spread spectrum version is the one that passes a radiated scan inside a closed enclosure.

The 15 uA no-load current is what makes the module usable as an always-on rail. A monitor that has to keep a 3.3 V housekeeping rail alive while the rest of the board is off cannot afford a millamp of standing current, and a discrete converter with a feedback divider and a switching controller typically draws several times that. The 200 us start up delay plus the SS/TR ramp gives a controlled sequence without an external supervisor, which is one less part on a crowded board.

Buyer questions on the TPSM82813SSILR

What is the difference between the SIL and the PVC body? The PVC body is the 13 pin MagPack package with the inductor shielded on the side, and it is offered on the 1 A and 2 A members. The SIL body is the 14 pin uSiL with the inductor on top, which is the lower height option and the one that carries the 3 A and 4 A members.

Can two rails be sequenced with this module? Yes. The SS/TR pin tracks an external voltage, so a second rail can follow the first with a resistor divider setting the ratio, and the power good flag can hold the second rail off until the first is in window.

Does spread spectrum affect the output accuracy? No. The modulation moves the switching frequency by a small percentage and the regulation loop follows it. The 1 percent accuracy figure is specified in PWM mode with the modulation active.

Buying this part through a component supplier

The SIL and PVC bodies are different footprints, and the S suffix changes the emission behaviour without changing the pin out, so the order code has to be read carefully on a purchase order. We supply the SIL codes with the marking and date code recorded through date code management, and the pin to pin cross reference page shows which members of the family share a footprint. For a programme that needs the same rail from a second source, how to verify a drop in replacement sets out the measurements that decide it.