Contact Us

TPSM365R6RDNR

Brand: Texas Instruments
Texas Instruments TPSM365R6RDNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPSM365R6RDNR — Power Management & Signal Chain | Superb Automation

TPSM365R6RDNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPSM365R6RDNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPSM365R6RDNR: the same 65 V module with a mode pin instead of a frequency resistor

The TPSM365R6RDNR uses the same 11 pin module body as the F version and answers a different question. Where the F version holds one frequency, this one carries a MODE/SYNC pin that sets either forced PWM or automatic PFM at light load, and accepts an external clock from 200 kHz to 2.2 MHz to lock several modules to one source. For a board that has four rails and one clock, that pin is the difference between four oscillators beating against each other and one clean frequency across the board.

The automatic mode is where the no-load current advantage lives. In PFM the module stops switching when the output is above its target and restarts when it droops, which is why the fixed output versions reach 0.67 uA typical at 13.5 V in and 1.2 uA at 24 V in. The adjustable version draws more because its feedback divider is always connected, 17 uA at 13.5 V. Neither number is a mistake: the fixed versions have the divider inside the module and can disconnect it, the adjustable one cannot because the divider is the customer's.

Key electrical data on the page

Input range3 V to 65 V after start, 70 V transient, UVLO release at 3.4 V to 3.6 V
Output600 mA, adjustable 1 V to 13 V, 300 mA and fixed 3.3 V or 5 V versions in the same family
ModesPFM/PWM automatic or forced PWM selected by the MODE/SYNC pin, 18 us at one level to latch the mode
Synchronisation200 kHz to 2.2 MHz external clock, 100 ns minimum pulse, 1.8 V high and 0.8 V low thresholds
No-load current1.2 uA typical at 24 V on the fixed versions, 18 uA on the adjustable version
EmissionCISPR11 class B as a complete module, pseudo random spread spectrum on by default
Thermaljunction to ambient 56.3 C per W, 10.7 C per W junction to top for a case measurement

Package, marking and reel data

BodyQFN-FCMOD RDN, 11 pins, 4.5 mm by 3.5 mm by 2.0 mm, same pad as the F and V3 versions
Reel3000 pieces on a 330 mm reel, 17.6 mm carrier, 8 mm pitch, quadrant Q1
PocketA0 3.80 mm, B0 4.80 mm, K0 2.30 mm, carrier width 12.0 mm
Finish and moisturetin, level 3 at 260 C, 168 hour floor life, so a partial reel needs a dry pack
Marking and grade365R6 on the top, rated -40 C to 125 C junction

Mode selection on a real board

The mode pin is not a strap that can be left floating. The module reads the level for 18 us and latches it, so a resistor divider or a direct tie to VIN or ground is required, and a pin left open with a long trace can pick up a level from a neighbouring node. The same pin accepts the synchronisation clock, which means a board that wants both auto mode and a locked frequency cannot have both: the clock implies forced PWM for as long as it is present, and the module reverts to the strap level when the clock stops.

This is the version to choose when the rail feeds a housekeeping load that is idle for long periods, such as a 4 to 20 mA transmitter loop, a battery backed sensor node on a 24 V bus, or the standby rail of an industrial gateway. The 1.2 uA at 24 V is the number that decides whether a battery lasts a season or a year, and it is only reachable on a fixed output version where the divider is not draining the input. An adjustable rail with an external divider pays 17 uA for the flexibility, which is still small but is seventeen times the fixed version.

Buyer questions on the TPSM365R6RDNR

Can the output be trimmed after the board is built? Yes on this version, because the feedback divider is external. That is the point of the adjustable members, and it is also why their no-load current is higher than the fixed 3.3 V part.

What happens if the sync clock disappears? The module reverts to the level on the mode pin. If the pin is tied high it keeps forced PWM at the internal frequency, if tied low it returns to automatic mode.

Is the module rated for a 48 V telecom rail? Yes, 65 V is the operating ceiling and 70 V is the transient rating, so a 48 V rail with a load dump fits. The input capacitor has to be rated above the transient, not just above the nominal.

Buying this part through a component supplier

Three order codes share one pad on this module, which is convenient for a board and awkward for a store. We keep the marking recorded on every reel label and documented through date code management, and the incoming inspection plan page covers the checks that tell a 365R6 from a 365R6F before the reel reaches a machine. For a programme that needs a second source on the same pad, pin to pin cross reference is the page to start from.