Contact Us

TPS92513DGQR

Brand: Texas Instruments
Texas Instruments TPS92513DGQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS92513DGQR — Power Management & Signal Chain | Superb Automation

TPS92513DGQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS92513DGQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS92513DGQR: a 42 V buck driver whose current setpoint is a voltage, not a resistor

The TPS92513DGQR is a 1.5 A buck LED driver with a 220 milliohm high side switch and a 4.5 V to 42 V input, and its unusual feature is the way the current is set. Instead of trimming a sense resistor, the part takes a voltage on the IADJ pin from 0 V to 1.8 V and scales the sense threshold from 0 V to 300 mV, so a controller or a trim pot can move the LED current across the full range without switching resistors in and out. A 0.18 V signal gives a 30 mV threshold, a 1.2 V signal gives 200 mV, and both are specified over the -40 C to 125 C junction range with a tolerance of a few percent. The 5 percent current accuracy figure on the front page is the number to quote to a customer who asks how close the light output will be from unit to unit.

Dimming is separate again. The PWM pin takes a logic signal and gates the output without touching the setpoint, which gives a contrast ratio above 100 to 1 with a clean off state, while the IADJ path gives about 10 to 1 of analog range with no off state at all. Using both is the usual arrangement: IADJ sets the brightness of the fixture and PWM handles the deep dimming at the bottom of the range.

Key electrical data on the page

Input range4.5 V to 42 V, and 60 V on the HV suffix, with the same body and pin count
Output current1.5 A with a 220 milliohm high side switch, 375 milliohm maximum at 6 V of gate drive
Current setpoint0 V to 300 mV threshold set by 0 V to 1.8 V on IADJ, 191 mV to 210 mV at 1.2 V
Accuracy5 percent on LED current, sense threshold 285 mV to 309 mV at the 300 mV setting
Switching100 kHz to 2 MHz set by resistor, external clock can overdrive the oscillator on multi string boards
Quiescent337 uA to 407 uA not switching, 11.5 uA in shutdown, UVLO pin threshold 1.12 V to 1.30 V
Thermaljunction to ambient 66.7 C per W, junction to case 15.4 C per W at the pad

Package, marking and reel data

BodyHVSSOP DGQ, 10 pins, 3 mm by 3 mm with a PowerPAD on the underside
Reel2500 pieces on a 330 mm reel, 12.4 mm carrier, 8 mm pitch, quadrant Q1
PocketA0 5.30 mm, B0 3.40 mm, K0 1.40 mm, carrier width 12.0 mm
Finish and moisturenickel palladium gold with a gold flash, level 1 at 260 C, unlimited floor life
Marking and grade92513 on the top, rated -40 C to 125 C junction

Where the analog setpoint earns its place

Street lighting and emergency lighting are the two applications where this pin matters. A street light with a photocell and a dimming schedule wants the current to follow a 0 V to 1.8 V control voltage from the controller, and a fixture that has to hold a fixed output for a ten year life wants the setpoint to come from a reference rather than a resistor tolerance. Emergency luminaires use the same trick to run at reduced current on battery, which stretches the runtime without a second driver.

The 42 V input covers a 24 V or 36 V DC bus with margin, and the HV suffix extends the same circuit to 60 V for a 48 V bus. Because the oscillator can be overdriven from an external clock, several of these drivers on one board can run at a common frequency, which removes the beat frequencies that make a multi string board buzz and makes the input filter a single calculation instead of one per string. The adjustable UVLO with hysteresis lets a battery powered fixture stop at a chosen input voltage and restart above it, which is the behaviour a solar lamp needs.

Buyer questions on the TPS92513DGQR

Can the output current be zero? The IADJ range starts at 0 V and the threshold follows to zero, so the current can be taken down to a very low level. It does not switch the output off, though; that is what the PWM pin is for.

How is the 5 percent accuracy measured? It is the LED current against the value set by IADJ over temperature and input voltage, with the sense resistor tolerance excluded. A build that needs tighter current uses a 0.5 percent sense resistor.

What is the purpose of the separate UVLO pin? It sets the input voltage at which the driver starts and stops, independent of the internal supply threshold. On a 24 V battery the pin can hold the light off below 21 V and restart above 22 V.

Buying this part through a component supplier

The DGQ body is a 3 mm square with a thermal pad, and the 250 piece DGQT reel exists for prototypes while the 2500 piece DGQR covers production, which is a useful pair to know when a first build is four hundred boards. We supply both against the BOM line and record the finish and the date code through date code management. When a lighting programme is moving from a reference part to a second source, the power management cross reference puts the 42 V and 60 V drivers side by side, and how to reduce component cost covers the body and reel choices that move the unit price.