Contact Us

TPS923652DMTR

Brand: Texas Instruments
Texas Instruments TPS923652DMTR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS923652DMTR — Power Management & Signal Chain | Superb Automation

TPS923652DMTR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS923652DMTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS923652DMTR: 2 A of boost current with a 150 milliohm switch and 65 V of headroom

The TPS923652DMTR is the 2 A member of the same TPS92365x family as the 1 A part, in the 14 pin VSON DMT body of 4.5 mm by 3.0 mm. The switch resistance drops to 150 milliohm and the cycle by cycle limit rises to 3 A, which is the pair of numbers that sets how much string current the part can hold at a given input. The switching frequency is not fixed by the body here, it is set by a resistor from 100 kHz to 2.2 MHz, and the 652 member does not carry spread spectrum while the 653 member does. That single difference is worth checking on a purchase order, because the two codes are otherwise identical and the marking differs only in the digit after the T.

The dimming set is the same as the rest of the family: 256 to 1 analog, 150 ns PWM pulse, 2000 to 1 hybrid at 20 kHz and 1,000,000 to 1 flexible dimming at 120 Hz. A 2 A string in a stage light or a marine lamp is usually dimmed at the low end for a long time, and the 1.17 percent sense floor at 1.17 percent of the 200 mV reference is what keeps that low end stable rather than flickering between two codes.

Key electrical data on the page

Input range4.5 V to 65 V, UVLO rising 3.0 V to 3.4 V, falling 2.8 V to 3.2 V
Output current2 A class, switch limit 2.6 A to 3.6 A, and 4 A members of the family at 5.8 A to 7.6 A
Switch150 milliohm low side NMOS, minimum on and off time 100 ns each
Switching100 kHz to 2.2 MHz set by resistor, spread spectrum on the 653 and 655 members only
Current sense200 mV at 100 percent duty, 12.5 mV equivalent at 12.5 percent duty, 1.17 percent floor
Internal rail5.15 V LDO at 47 mA limit, 10 mA operating current at 2.2 MHz
Quiescent0.8 uA to 2.3 uA shutdown, 2.5 mA with the PWM input low and the device enabled

Package, marking and reel data

BodyVSON DMT, 14 pins, 4.5 mm by 3.0 mm, exposed pad under the switch
Reel3000 pieces on a 330 mm reel, 12.4 mm carrier, 8 mm pitch, quadrant Q1
PocketA0 3.30 mm, B0 4.80 mm, K0 1.20 mm, carrier width 12.0 mm
Finish and moisturenickel palladium gold, level 1 at 260 C, unlimited floor life
Marking and gradeT3652 on the top, rated -40 C to 125 C junction

Choosing between the 652 and the 653

The 653 adds spread spectrum, which sweeps the switching frequency around the set point by a small percentage. On an EMI scan that moves a narrow peak into a wider and lower hump, which is often the difference between passing a radiated limit and adding a shield. The cost is a small amount of low frequency ripple in the light output, and in a lamp that is filmed that can be visible. A stage light or an architectural fixture without a camera in the room takes the 653. A machine vision lamp that is strobed takes the 652, because the emission of a fixed frequency is easier to notch at the receiver than a frequency that moves.

The 2.2 MHz upper end of the frequency range is where the inductor becomes small enough to fit on the back of a 20 mm LED board, and the 100 kHz lower end is where the switching loss is low enough to keep a sealed fixture cool. The resistor at the RT pin sets that choice, and the minimum on and off times of 100 ns bound how far the duty can move at either end. At 2.2 MHz a 100 ns on time is 22 percent of the period, so a string that needs 5 percent duty at the top of the input range cannot be regulated at that frequency and the resistor should be chosen for a lower one.

Buyer questions on the TPS923652DMTR

Can this run from a 48 V rail? Yes, 65 V is the ceiling and the part is a boost, so the string can sit above a 48 V input up to the switch rating. The inductor and the freewheel diode then carry the full string current and have to be chosen for 65 V of reverse voltage.

What is the difference from the 1 A part? The switch resistance, the current limit and the body. The control scheme, the dimming options and the LDO are the same, so a board can move from the eight pin SOT to the fourteen pin VSON without a change in the sense resistor value or the control scheme.

How accurate is the current at low dimming? The sense threshold at 1.17 percent of full scale is specified between 0.82 percent and 1.52 percent, so the low end of the range is where the tolerance is widest. A build that needs a precise 1 percent level uses the analog input with a calibrated source rather than the hybrid mode.

Buying this part through a component supplier

The 14 pin VSON and the 12 pin WSON of this die are not interchangeable on a board even though they are the same silicon, so a purchase order has to carry the body letter and the reel quantity together. We hold both codes against the BOM line and document the body on the shipment through date code management. When the 652 is not available, the pin to pin cross reference shows whether the 653 can be substituted with only an EMI retest, and how to verify a drop in replacement sets out the three measurements that decide it.