Contact Us

TPS92360DCKR

Brand: Texas Instruments
Texas Instruments TPS92360DCKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS92360DCKR — Power Management & Signal Chain | Superb Automation

TPS92360DCKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS92360DCKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS92360DCKR: 38 V boost LED backlight driver in a five pin SC70

TPS92360DCKR is a step up converter with an integrated switch that regulates a series LED string by current rather than by voltage in a SC70 (DCK) body of 5 pins. The switch is rated 40 V and the device holds the string at or below 38 V, so it covers a panel of up to about ten white LEDs in series from a single lithium cell or a 5 V rail. LED current is set by one resistor from the feedback pin to ground and dimming is done by a pulse width modulated signal on the control pin, with a 204 mV reference that keeps the sense resistor small.

Order code and package

Order code read outTPS92360 DCK R: device TPS92360, DCK five pin SC70, R large tape and reel
PackageSC70 (DCK), 5 pins, 2.00 mm by 1.25 mm body
Carrier in the vendor addendumTPS92360DCKR, 3000 pieces on a large reel, the only orderable row published; no small reel and no A or B suffix appear
Moisture levelLevel 1, 260 degrees unlimited floor life, which is why this part needs no dry pack control on the line
Lead finishNickel palladium gold with a silver spot, quoted by the vendor as POST-PLAT AG SPOT or SN
Operating junction rangeminus 40 to plus 150 degrees Celsius, storage minus 65 to plus 150
Absolute maximum7 V on supply, control and feedback pins, 40 V on the switch drain

Electrical parameters that decide the application

Input voltage range2.7 V to 5.5 V, taken from one lithium cell, a 3.3 V rail or a 5 V rail
Undervoltage lockout2.5 V typical on the way up and 2.3 V on the way down, so a cell that sags under load does not restart the boost
Feedback reference204 mV with a 188 to 220 mV window at 25 degrees, which sets the LED current tolerance
Switch on resistance0.35 ohm typical and 0.7 ohm maximum, so the conduction loss at 1 A is about 0.35 W
Switch current limit1.2 A minimum, 1.8 A typical, 2.4 A maximum, and a start up limit of 0.72 A that steps to full limit 6.5 ms at a time
Switching frequency1.2 MHz nominal between 0.75 and 1.5 MHz, above the audio band and small enough for a 1 uH inductor
Output overvoltage36 V minimum, 37.5 V typical, 39 V maximum, which is the open string protection threshold
Quiescent current0.45 mA maximum into the supply with the control pin high
Shutdown current2 uA maximum, so a handheld left off does not drain the cell
Dimming input1.2 V logic high, 0.4 V logic low, internal pull down, and a low period longer than 2.5 ms turns the device off
Thermal shutdown160 degrees with 15 degrees of hysteresis
Feedback bias current2.5 uA maximum, which is the leakage that shifts the current setting at low LED currents

Order code decode and what sits beside it

TPS92360the part on this page, one string, 38 V ceiling, 1.2 A switch limit
DCK bodythe five pin SC70, the only package published for this device
R suffixlarge tape and reel, 3000 pieces, which is the carrier a production line normally receives
Two string panelsneed either two devices or a part with a higher switch current, since this one drives a single string
Parallel stringscan share one device only if the total current stays inside the 1.2 A minimum limit

Points to check before this part goes on a BOM

The 1.2 A figure is a minimum switch current limit, not an output current. In a boost, the switch carries the inductor current, and the average LED current is always lower than that once the duty cycle is taken into account. A string of eight LEDs at 3.2 V each from a 3.7 V cell runs at a duty near 0.89, so the inductor current is close to the LED current and the 1.2 A floor is what actually caps the string. From a 5 V rail the duty is lower and the same limit buys more LED current, which is why the rail matters more than the headline.

The overvoltage threshold protects an open string and has a wide window. The 36 to 39 V spread means a string that sits at 35 V at cold temperature can trip the protection on a unit whose threshold is at the bottom of the window. When a panel draws fewer LEDs than the ceiling allows, the margin should be checked at the coldest operating point, because forward voltage rises as temperature falls and that is the case that opens a string electrically.

Start up is deliberately gentle. The current limit starts at about 72 percent of the full value and steps up every 6.5 ms, so the inrush into the output capacitor does not pull the battery below its own undervoltage level. In a handset this is the difference between a clean start and a brown out reset, and it also means the total turn on time is a few tens of milliseconds rather than instant.

Dimming through the control pin regulates the reference voltage rather than chopping the string. That keeps the converter in continuous conduction and avoids the audible buzz that comes from bursting the LED current, but it also means very low dimming duty pushes the loop into a low reference where offset and the 2.5 uA feedback bias current start to matter. Panels specified down to one percent brightness should be checked at that point rather than at full scale.

The part has no enable pin separate from the control pin, so the same signal both dims and shuts the device down. A logic low for longer than 2.5 ms ends switching and drops the supply current to the 2 uA region, which recovers the standby budget of a portable product without a second control line. A pulse train that happens to contain a low period longer than that window will shut the driver off instead of dimming it, so the dimming source has to keep its off time short.

Where this order code fits

This driver suits handheld and panel backlights where the string is short and the rail is a single cell: handsets, tablets, portable media players, handheld terminals, blood glucose meters and instrument displays that need a dimmable white backlight from 2.7 V to 5.5 V. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can it drive two strings in parallel from one device? Only when the combined current stays under the 1.2 A minimum switch current limit and the two strings have matched forward voltage. Unmatched strings share current unevenly, and the lower voltage string takes most of it, so a series ballast resistor or a second driver is the safe route.

What sets the LED current? One resistor between the feedback pin and ground. The device holds 204 mV across it, so 20 ohm gives about 10 mA and 4 ohm gives about 51 mA. The resistor tolerance and the 188 to 220 mV reference window together set the spread.

Does it need an external compensation network? No. Compensation is internal, and the data sheet gives the output capacitor range that keeps the loop stable. Fitting a much larger output capacitor than the recommended value is the usual cause of slow start or audible whistle at low dimming levels.

Is the part available in a small reel? The published addendum lists the 3000 piece large reel only. A prototype quantity normally comes from a cut reel or from a distributor who breaks the large reel, and that is worth confirming on the offer rather than assuming.

How is it handled on the line? Moisture level 1 with unlimited floor life at 260 degrees, so no baking and no dry pack shelf life applies. That is a practical advantage in low volume builds where parts sit on the shelf between runs.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.