TPS922055DRRR
Product Specifications
TPS922055DRRR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS922055DRRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS922055DRRR: 65 V in, 4 A out, and a thermal foldback curve you set with one resistor
The TPS922055DRRR is the 4 A member of the TPS92205x family, a non synchronous buck LED driver that takes 4.5 V to 65 V in and switches a single low side FET of 150 milliohm against an external inductor and diode. Non synchronous sounds like a step backwards until the application is a 48 V street light or a horticulture panel, where the freewheel diode is a Schottky with a forward drop that costs less than the silicon area of a second FET would cost in the same thermal budget. The 65 V rating is what makes the part usable on a 48 V rail that sees 60 V transients, and the common anode connection is what makes it usable on a single sided aluminium board, because the LED string shares the input rail and only the low side has to be routed.
The switching frequency is set by a resistor from 100 kHz to 2.2 MHz, and the 53 and 55 members add spread spectrum to move the emission around the band instead of parking it on one harmonic. Dimming is the part that sells this family: 256 to 1 in analog, a 150 ns PWM pulse, 2000 to 1 hybrid at 20 kHz PWM and 1,000,000 to 1 flexible dimming at 120 Hz. That last figure is what a camera needs when the light has to stay flicker free at any exposure.
Key electrical data on the page
| Input range | 4.5 V to 65 V, UVLO rising 3.0 V to 3.4 V, falling 2.8 V to 3.2 V |
| Output current | 4 A class, cycle by cycle switch limit 5.2 A to 7 A, 2 A members limit at 2.6 A to 3.6 A |
| Switch | 150 milliohm low side NMOS, minimum on and off time 100 ns each |
| Switching | 100 kHz to 2.2 MHz set by resistor, spread spectrum on the 53 and 55 members |
| Current sense | 200 mV at 100 percent duty, 12.5 percent of that at 12.5 percent duty, 1.17 percent at the floor |
| Internal rail | 5.15 V LDO at 47 mA limit, which is enough to drive a gate and a small housekeeping load |
| Quiescent | 0.8 uA to 2.3 uA shutdown, 2.5 mA with the PWM input low and the device still enabled |
Package, marking and reel data
| Body | WSON DRR, 12 pins, 3.0 mm by 3.0 mm, exposed pad for the switch heat |
| Reel | 3000 pieces on a 330 mm reel, 12.4 mm carrier, 8 mm pitch, quadrant Q2 |
| A0 3.30 mm, B0 3.30 mm, K0 1.10 mm, carrier width 12.0 mm | |
| Finish and moisture | nickel palladium gold, level 1 at 260 C, unlimited floor life |
| Marking and grade | T22055 on the top, rated -40 C to 125 C junction |
What the foldback resistor buys
A 4 A driver in a 3 mm body has one hard limit: the switch dissipation plus the diode dissipation plus the inductor loss has to leave the junction below 125 C. In a street light head the driver sits on the same aluminium as the LEDs, and the LED board is at 70 C on a summer afternoon. The foldback feature starts reducing current when the junction reaches 130 C, and the curve shape is set by the resistor at the RTEMP pin, so an integrator can decide whether the light loses 10 percent or 40 percent of its output at the top of the temperature range. That is a better outcome than a hard shutdown at 165 C, which in a street light reads as a failed luminaire.
The CC/CV mode is the second feature that gets used in practice. A driver that regulates current into a string and voltage into a battery can charge a battery pack during a power failure and then drive the emergency LED string from the same board, which is what a maintained emergency luminaire needs. The CV loop shares the same sense resistor pair, so no second current path is needed.
Buyer questions on the TPS922055DRRR
Can the part drive a string above the input voltage? No. This is a buck, so the string voltage has to stay below the input. For a 4 to 8 LED string from a 12 V rail the boost and buck boost members of the 65 family are the ones to look at, and the 2 A members share the same control scheme.
Does spread spectrum change the output ripple? It changes the switching frequency slightly around the set point, so the ripple amplitude stays about the same while the emission spreads over a band. The 52 and 54 members without it are the ones to use when a fixed frequency is a system requirement.
What sets the analog dimming floor? 256 to 1 in analog mode comes from the 200 mV sense reference and the 8 bit resolution of the ADIM input, with the analog input frequency limited to 156 kHz at 6 bit and 39 kHz at 8 bit.
Buying this part through a component supplier
Lighting builds are quoted in thousands and the driver is the part that decides whether the order can ship, so availability is usually the first question. The power management cross reference lists the 65 V buck drivers by body, pin count and current class, and safety stock planning is where a lighting customer plans the buffer for a part with a 12 week channel lead time. When a build needs the 14 pin VSON body instead of the 12 pin WSON, the same page shows the marking change so the pick and place program and the inspection plan move together.