TPS92201DRVR
Product Specifications
TPS92201DRVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS92201DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS92201DRVR: a 5.5 V buck driver with 0.1 uA of shutdown current
The TPS92201DRVR is the small rail member of the LED driver line: 2.5 V to 5.5 V in, 1.5 A out, a synchronous buck with 220 milliohm and 170 milliohm switches, running at a fixed 1.5 MHz. It is built for battery equipment, which is why the shutdown current is specified at 0.1 uA typical and 0.5 uA maximum rather than in milliamps, and why the switching duty cycle can reach 100 percent: a single cell lithium pack at 3.6 V driving one white LED at 3.2 V needs the switch to stay on almost continuously, and a part that tops out at 90 percent duty would drop out of regulation there.
The 100 mV feedback reference sets the sense resistor the same way the larger parts do. At 500 mA the resistor is 200 milliohm, and the tolerance at 50 percent PWM duty is 50 mV plus or minus 8 percent at a 20 kHz input and plus or minus 10 percent at 200 kHz. That wider window at the higher frequency is worth reading twice: the dimming accuracy is specified against the PWM frequency, so a board that dims a camera illuminator at 200 kHz gets a looser current than the same circuit at 20 kHz.
Key electrical data on the page
| Input range | 2.5 V to 5.5 V, UVLO rising 2.3 V to 2.4 V, falling 2.1 V to 2.2 V, 0.1 V of hysteresis |
| Output current | 1.5 A constant, high side current limit 1.9 A to 2.16 A |
| Feedback | 100 mV at full duty, 92 mV to 104 mV, and 50 mV at half duty with the tolerance above |
| Switches | 220 milliohm high side and 170 milliohm low side, 1.5 MHz fixed switching |
| Duty cycle | up to 100 percent, which keeps regulation with a 3.2 V string on a 3.6 V pack |
| Dimming | PWM input 20 kHz to 200 kHz, duty 1 percent to 100 percent, minimum on time 5 us |
| Quiescent and shutdown | 0.52 mA typical operating, 0.1 uA typical shutdown into the input |
Package, marking and reel data
| Body | WSON DRV, 6 pins, 2 mm by 2 mm, thermal pad on the underside |
| Reel | 3000 pieces on a 178 mm reel, 8.4 mm carrier, 4 mm pitch, quadrant Q2 |
| A0 2.30 mm, B0 2.30 mm, K0 1.15 mm, carrier width 8.0 mm | |
| Finish and moisture | nickel palladium gold over the copper lead frame, level 1 at 260 C, unlimited floor life |
| Marking and grade | 34LH on the top, rated -40 C to 85 C ambient |
Two versions, one difference that matters
The plain TPS92201 holds a forced PWM mode across the whole load range, so the ripple stays small and predictable at light current, and the quiescent current is 0.52 mA typical. The TPS92201A drops into pulse frequency modulation when the load falls, which trades ripple for efficiency and pulls the operating current to about 0.63 mA typical in the same no load condition. For an IR emitter that is strobed, the plain version is the safer choice because the switching behaviour does not change with duty. For a status LED that stays on at low current for hours, the A version is the one that keeps the battery alive.
The package is 2 mm by 2 mm with six pins and needs no bootstrap capacitor, because the high side switch is driven from an internal rail. What it does need is a solid ground under the thermal pad and an input capacitor within 2 mm of the VIN pin; at 1.5 MHz the loop from input capacitor through the switches and back is the whole EMI story. The output capacitor can be 10 uF ceramic in most builds, and the feedback filter is a single 10 k resistor and 100 nF capacitor at the PWM pin.
Buyer questions on the TPS92201DRVR
Does the part work from two AA cells? Yes, the input floor is 2.5 V and the UVLO releases at 2.4 V maximum, so a fresh pair of alkaline cells runs it. Below 2.1 V the part stops and waits for the input to rise again, which protects the cells.
How low can the PWM input go? The duty cycle floor is 1 percent with a 5 us minimum on time, so a 20 kHz signal can go down to 5 us of on time. Below that the pulse is ignored rather than stretched, which is the honest behaviour for a shutter synchronised strobe.
What is the reason for the 100 percent duty rating? A white LED at 3.2 V from a 3.6 V pack leaves only 0.4 V of headroom, and at 1.5 A that is 600 mW of loss in the switch pair. The part drops into full conduction instead, and the current is then set by the resistor and the battery internal resistance.
Buying this part through a component supplier
A 2 mm WSON driver is typically a line item on a board with a dozen other small parts, and the reel quantity of 3000 rarely matches the build. We supply the order code against the BOM line, keep the date code documented on the shipment through date code management, and when the part is missing from the channel the BOM shortage recovery route looks for the same die in another body before a board change is considered. The pin to pin cross reference is the page to check when the only available version is the SOT-5X3 DRL body at 4000 per reel.