Contact Us

TPS7B8350QDCYRQ1

Brand: Texas Instruments
Texas Instruments TPS7B8350QDCYRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7B8350QDCYRQ1 — Power Management & Signal Chain | Superb Automation

TPS7B8350QDCYRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7B8350QDCYRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7B8350QDCYRQ1: 5 V, 150 mA and only 18 uA of standing current

The TPS7B8350QDCYRQ1 is the 5 V member of the TPS7B83-Q1 line, a 150 mA regulator with an 18 uA typical quiescent current, a 3 V to 40 V input window and 42 V of transient tolerance. Accuracy is plus or minus 1 percent, which is a full step tighter than the older 40 V parts, and the SOT-223 body gives the tab a place to put its heat. The part is AEC-Q100 grade 1 with a junction range to 150 C.

The transient behaviour is the other half of the case. Output deviation is plus or minus 2 percent during a cold crank, and the architecture is built to minimise overshoot when the input recovers from dropout, which is the moment a 5 V rail usually pushes a spike into the logic behind it. Current limit is 220 mA to 260 mA, a brickwall rather than a foldback, so a short holds the rail at a bounded current instead of oscillating.

Key electrical data for the 5 V part

Input range3 V to 40 V, 42 V maximum, with 45 V transients tolerated
Output5.0 V fixed at plus or minus 1 percent over line, load and temperature
Output current150 mA, current limit 220 mA to 260 mA
Quiescent current18 uA typical at light load, which is what keeps a parked module alive
Dropout230 mV maximum at 150 mA for the 3.3 V option, similar for the 5 V point
Transientplus or minus 2 percent deviation during a cold crank and on recovery from dropout
Junction rangeminus 40 C to 150 C, grade 1 qualified

Package, marking and reel data

BodySOT-223 DCY, 4 pins, tab soldered to the board, 330 mm carrier
Reel2500 pieces, large tape and reel, quadrant Q3
Finish and moistureSN, level 2, 260 C peak reflow, one year floor life
Marking7B8350
Suffix rowsM3 and W rows carry the same die with a different marking convention and the same reel size

Where a 1 percent 5 V rail earns its cost

CAN transceivers, sensor supply pins and always-on logic all tolerate a few percent, so why pay for 1 percent? Because the 5 V rail often feeds a reference or a ratiometric sensor, and a 3 percent window on a 5 V rail is 150 mV of error that lands directly in the measurement. A 1 percent part costs little more than a 3 percent one and removes that term from the calibration, which is the cheaper place to remove it.

The 18 uA quiescent current then decides whether the module can stay connected. A 40 uA drain on a 60 Ah battery is 1 mAh per day, which is acceptable over a two week parking period; a 300 uA drain is not. The TPS7B83-Q1 sits in the first category, and that is why it turns up in body modules, gateways and battery management units that are never really switched off. The 3 V to 42 V window also means the same code survives a jump start and a load dump without a clamp, which removes two parts from the front end of the board. The 1 percent window then holds that same rail steady through the event, so the logic behind it never sees the transient that the protection parts were there to absorb. A clamp is still worth keeping on the input for the load dump itself, but it no longer has to protect a 40 V part from a 60 V event.

Buyer questions on the TPS7B8350QDCYRQ1

What are the M3 and W suffix rows? They are the same die and the same reel size with a different part marking convention, used where a customer's traceability system expects a specific code. Electrically the rows are equivalent, so the choice is made on the marking rule of the assembly house.

Is the part stable without an output capacitor? No. The data sheet requires a ceramic output capacitor for stability, and the transient figures assume it. Removing it is the most common cause of a rail that looks fine at room temperature and oscillates cold.

How does the part behave when the input is below the output? It enters dropout and the output follows the input down, with the recovery overshoot bounded by the architecture. That is the behaviour that keeps a 5 V rail from spiking when a crank event ends.

Buying this regulator through a component supplier

The suffix rows are the trap in this family: three codes, one die, and a line that reads the wrong column will reject a good reel. Our power management cross reference prints the marking next to each code. Where a customer is qualifying a second body, supplier quality audit covers what the incoming inspection should confirm.