Contact Us

TPS7B8233QKVURQ1

Brand: Texas Instruments
Texas Instruments TPS7B8233QKVURQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7B8233QKVURQ1 — Power Management & Signal Chain | Superb Automation

TPS7B8233QKVURQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7B8233QKVURQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7B8233QKVURQ1: a 3.3 V 300 mA automotive regulator rated to 40 V of input in a TO-252 body

TPS7B8233QKVURQ1 is an automotive low dropout regulator that runs from a battery line up to 40 V with 45 V of load dump tolerance and 2.7 microamps of quiescent current in a TO-252 (KVU) body of 5 pins. It delivers 300 mA at 3.3 V fixed, with 2 per cent accuracy and a quiescent current of 2.7 microamps typical at light load, 5 microamps maximum, and 300 nA in shutdown. The input window starts at 3 V, so the part keeps regulating through a cold crank and through start stop events rather than dropping the rail. The TO-252 body of 6.6 mm by 10.11 mm has a junction to ambient figure of 31.1 C per watt, which is the number that lets it hold current in a hot engine bay. Short circuit and overcurrent protection are internal, and the part is AEC-Q100 qualified to grade 1 with a junction range to 150 C.

Order code and package

TPS7B8233QKVURQ1the 3.3 V fixed member in the 5 pin TO-252 body, which is the wettable flank version for automated optical inspection of the solder joint
Other bodiesthe same die ships in the 6 pin WSON with wettable flank at 72.8 C per watt, the 8 pin HVSSOP and the HTSSOP, so the thermal figure changes by more than a factor of two across bodies of the same part number family
TPS7B8250 and TPS7B8225the 5.0 V and 2.5 V members, same 300 mA rating and same bodies, and the 700 mV dropout figure in the headline belongs to the 5 V member at 200 mA rather than to the 2.5 V one
Grade 0 optionthe family carries a grade 0 variant for minus 40 C to 150 C ambient with a junction range to 165 C, which is the option for a body controller mounted next to the engine rather than behind the dash
TPS7B81-Q1the 150 mA member of the same range with the same 40 V window, which is the smaller alternative when the load is a microcontroller and a CAN transceiver rather than a module
Pin count5 pins in the TO-252 with the tab as the output, so the tab is electrically live and the copper under it is part of both the thermal and the electrical path

Electrical parameters that decide the application

Input voltage3 V to 40 V recommended with 45 V of transient tolerance, so a 12 V battery line with a load dump and a 24 V truck line are both inside the same window
Output voltage3.3 V fixed on this code, from a family set of 2.5 V, 3.3 V and 5 V
Output current300 mA maximum, with the TO-252 tab and the copper under it setting how much of that current survives at 125 C ambient
Quiescent current2.7 microamps typical and 5 microamps maximum at light load, with 300 nA in shutdown, which is the figure that keeps a parked vehicle from draining its battery over weeks
Accuracy2 per cent over line, load and temperature, which is enough for a microcontroller rail and a CAN transceiver supply
Dropout voltage700 mV maximum at 200 mA on the 5 V member, which is the worst case in the family and the figure to use when the rail has to hold through a cold crank
Cold crankoperation down to 3 V of input is what carries the rail through a crank event where the battery line falls to 4 or 5 V for tens of milliseconds
Output capacitor1 microfarad to 200 microfarad of ceramic with an ESR window from 1 milliohm to 5 ohm, which is wider than most regulators of this class and allows a standard X7R part
Protectionshort circuit and overcurrent protection are internal, and thermal shutdown protects the pass element when the ambient rises above what the copper can carry
Reverse currentthe pass element blocks reverse current while the part is disabled, which keeps the output from feeding a battery line that has been disconnected
QualificationAEC-Q100 grade 1 with a junction range of minus 40 C to 150 C, and a grade 0 option to 165 C junction for a hotter mounting position
Thermal31.1 C per watt junction to ambient in the TO-252, against 72.8 C per watt in the 6 pin WSON, which is the reason the larger body is chosen on a 300 mA rail

Bodies and grades in the TPS7B82-Q1 range

TPS7B8233QKVURQ1this order code, 3.3 V fixed in the 5 pin TO-252 with wettable flanks, tab connected to the output
TPS7B8250 and TPS7B8225the 5.0 V and 2.5 V members, and the 700 mV dropout headline belongs to the 5 V member at 200 mA rather than to this output
Bodiesthe same die in the 6 pin WSON at 72.8 C per watt, the 8 pin HVSSOP, the TO-252 at 31.1 C per watt and an HTSSOP, so the thermal answer changes by more than a factor of two
Grade 0 optionextends the ambient to 150 C and the junction to 165 C for a module mounted next to the engine rather than behind the dash
TPS7B81-Q1the 150 mA member of the same range, same 40 V window, which is the smaller choice for a microcontroller and a transceiver
Cold crankthe 3 V floor is what carries the rail through a crank where the battery line falls below 5 V for tens of milliseconds
Quiescent current2.7 microamps typical and 5 microamps maximum at light load, with 300 nA in shutdown

Points to check before this part goes on a BOM

The tab of a TO-252 is the output, not ground. On this body the tab is connected to VOUT, so a heatsink pad or a copper pour under the tab sits at 3.3 V. That is the detail that turns a working prototype into a shorted board when a mounting screw or a thermal pad touches something it should not.

5 microamps maximum is the number for the battery budget. The typical figure is 2.7 microamps and the maximum over temperature is 5. On a parked vehicle the module draws that current for weeks, and the difference between the typical and the maximum is the difference between a battery that starts and one that does not after a cold month.

40 V of input is not 40 V of dissipation. At 24 V in and 3.3 V out, delivering 300 mA dissipates 6.2 W, which no TO-252 survives at 125 C ambient without a copper plane. The real operating point is a high input voltage at a modest current, or a low input voltage at the full current, and the thermal table decides which.

Cold crank is the reason for the 3 V floor. During a crank the battery line can fall to 4 V or below for tens of milliseconds, and a regulator that stops at 6 V drops the rail and resets the module. A 3 V floor keeps the microcontroller and the CAN transceiver alive through the event, which is what the automotive qualification is testing.

The dropout figure in the headline is not for this voltage. 700 mV at 200 mA belongs to the 5 V member. On the 3.3 V member the dropout is lower, and a rail holding 3.3 V from a 4 V crank needs the curve for this output rather than the family headline.

Body choice changes the thermal answer, not the electrical one. The 6 pin WSON gives 72.8 C per watt and the TO-252 gives 31.1, on the same die and the same table. A board that moves between bodies to save area has to recheck the junction temperature at the same load, because the electrical limits have not moved but the thermal ones have.

An always on rail in a vehicle

A body control module, a gateway or a telematics unit has a rail that stays live with the ignition off, because it has to wake on a CAN frame or a key fob event. That rail draws its quiescent current for weeks at a time, and the regulator is the largest single contributor after the transceiver. A part that draws 2.7 microamps typical and 5 microamps maximum across the temperature range is what makes a three week parked period survivable on a healthy battery.

The second requirement on that rail is behaviour during a crank. The battery line can fall to 4 V while the starter turns, and a regulator that loses regulation there resets the module and loses its network state. The 3 V floor in this family is what keeps the module awake through the event and able to report a low voltage condition afterwards.

Why the TO-252 is still the body for a hot module

The 6 pin WSON is smaller and has a wettable flank, and its junction to ambient figure is 72.8 C per watt against 31.1 for the TO-252. On a 300 mA rail with 12 V of input, the dissipation is about 2.6 W, and the difference between those two figures is the difference between a junction that settles at 100 C and one that runs past its limit. The larger body is chosen for the thermal path, not for the assembly convenience.

Where this order code fits

an always on 3.3 V rail in a body controller, a gateway or a telematics unit that has to survive a cold crank and hold its quiescent current over a parked period Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

What is the highest input this part accepts? 40 V recommended with 45 V of transient tolerance. A 24 V truck line with a load dump is inside the transient figure, but a board that sees repeated load dumps should still clamp the input.

How much current does it draw with the ignition off? 2.7 microamps typical and 5 microamps maximum at light load, with 300 nA in shutdown. The maximum is the figure to use in a battery budget.

Can it hold 3.3 V during a cold crank? Yes, the input window starts at 3 V, so the rail holds while the battery line falls through 4 V for the duration of the crank. The output follows the input only when the input falls within the dropout of 3.3 V.

What does the grade 1 qualification cover? Minus 40 C to 125 C ambient with a junction range to 150 C. The grade 0 option extends the ambient to 150 C and the junction to 165 C for a hotter mounting position.

Is the tab connected to ground? No, the tab is the output on this body, so any copper or heatsink under it sits at 3.3 V and has to be treated as a live surface.

How does SUPERB handle the grade and body question? The offer names the exact ordering string, the body, the grade and the date code, because the same die ships in four bodies with thermal figures that differ by more than a factor of two.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.